MultiWii

scrat

Maybe ESC lost sync?

scrat

12mil will hold 2A with 30C ambient temp and allowed 50C temperature rise. I have no idea what the stall current of HS81MG is, I see some spec saying operating current is ~250-280mA, so I guess you will be fine with this? Thanks timecop! But for safety...I'll power servos from separate SBEC. I've f...

scrat

Hi fellow Naze32 users. Could someone tell me about how many Amps will hold original Naze32. I'll put FC into flying wing (maxi swift). I want to connect to FC: two digital servos (HITEC HS81MG), Rx (Rlink - 75ma@5v), GPS (RCTimer u-Blox CN-06 GPS Receiver V3.0) and MinimOSD v1.1 (m). Can I connect...

scrat

Hi fellow Naze32 users. Could someone tell me about how many Amps will hold original Naze32. I'll put FC into flying wing (maxi swift). I want to connect to FC: two digital servos (HITEC HS81MG), Rx (Rlink - 75ma@5v), GPS (RCTimer u-Blox CN-06 GPS Receiver V3.0) and MinimOSD v1.1 (m). Can I connect ...

scrat

It's working now. There was permissions problem. Debian or Ubuntu distro. Go to Terminal: type: ls -l /dev/ttyUSB0 crw-rw---- 1 root dialout 188, 0 maj 11 16:16 ttyUSB0 And then put user in dialout group with command: sudo usermod -a -G dialout <your user> Log out and log in and it's working

scrat

Thanks man! I'll try and post results.

scrat

Hi guys. One question. I'm using OS Debian 8. Have installed Google Chrome and baseflight configurator. But can connect Naze32. Whe FC is connected in configurator I see /dev/tty/USB0 but just get an error: Failed to open port.

What can I do?

Thx!

scrat

jaysonragasa wrote:I agree with the boxes! sometimes, it will take me 3 times to click it.

Click the box in upper left corner. For me it is working. Just one click.

scrat

LeoTheHuman wrote:Hi guys!

Just a quick check, should this work with multiwii 2.4 on atmega328P powered board? I've tried to connect to it and it didn't work out of the box. I'm able to debug it if it is supposed to work, but wanted to check before spending time on it.

Thanks!

No.

scrat

Latest baseflight configurator 0.61 doesn't save RC Expo setting in Receiver tab (always goes back to 0.65). But works normally (saves) setting in CLI.

scrat

For HoTT Graupner users.. I coded an interactive Text Mode in Cleanflight so that you can check and edit Cleanflight parameters directly from your TX as you do it with CLI in the Cleanflight-Configurator. As shown on the image below (views of the TX display), you access to specific pages through 2 ...

scrat

default is set nav_controls_heading = 1 so that means...coming home with nose forward and at home point turns like it was when taking off.

scrat

You are talking about FrSky D4R-II Rx and then t9x Rx? Which one you're using?

scrat

Every day with the multi wii is a new experience. When it works it works great, but when it doesn't who knows. The motors are all running erratically. Everything is calibrated. Everything is as it was before, but now the motors run at different speeds. What a mess. Do eeprom_clear and then load fre...

scrat

Question for the gallery: Why did the behaviour of the CLI change, so that now you have to type "save"? I was delighted when I found out the BF configurator did this automatically, and reconnected automatically, just by clicking another tab. Now I have to type save, wait for the board to ...

scrat

Sorry for asking. Did you fix bug for zeroing VELOCITY PID's in baseflight?

scrat

I'm using MAC - the latest OS. And bf conf. works perfect. Drivers are those: http://www.silabs.com/Support%20Documen ... Driver.zip. Uninstall bf conf. from Chrome and install again. Then try. And please check if you're not using USB cable just for charging.

scrat

scrat

Hello, first thank for super work on this project TimeCop. But I have small problem. If choice receiver PPM and activate Sonar (connect on RC input pins 7 trig and 8 to echo, voltage level is 3,3V) will blocked USB communication (Baseflight GUI). If I disconnected Sonar from pins 7,8 and restart FC...

scrat

Hi Bart.

There is a bug again in the latest version of MWii EZ-GUI when using with original baseflight. When setting PIDs....again VELOCITY goes all to 0. Could you be so kind and repair this bug.

Thanks.

scrat

I hope you've bought original Naze32 board.

scrat

Turn off Telemetry and GPS will work. I hope you've set in CLI feature GPS and for uBlox gps_type = 1 and gps_baudrate = 0.

scrat

If you're using AFRO ESC then just set in CLI minthrottle = 1064 and MAxthrottle = 1864

scrat

shorten boot pins and then connect fc to baseflight conf and flash firmware.

scrat

128k only.

scrat

Set I for YAW to at least 60. I have this set to 65 and it is ok. And have the latest version from BF Configurator.

scrat

hwurzburg wrote:Not sure BF has GPS_SBAS_MODE clisetting....Cleanflight does, however

Just check and you'll be suprised.

BF has this settings.

scrat

I have just set in BF Conf GPS TYPE=UBLOX and EU EGNOS and my lock time is now 20sec- 8 sats

then 30sec - 10 sats.

scrat

Hi, What's the CLI command to disable MAG sensor please? Thanks, Madison Not possible in software on Naze32. You could de-solder it if you have the equipment and know how. acc_hardware This is used to suggest which accelerometer driver should load, or to force no accelerometer in case gyro-only fli...

scrat

The first time I did this I didn't know that but even after removing the MinimOSD from my Naze I couldn't get into baseflight. Since then I sent that chip back thinking it was defective and bought a new one. This time after I had it set up, I attached my MinimOSD. When I powered the quad on, the qu...

scrat

manhocas wrote:Ok, so I flashed it with the 27ms firmware and still same issue. Any ideas where to start troubleshooting this?
Thanks again

I'm using the same Rx with 27ms refresh ...works perfectly. So don't bother. And update FC to the latest baseflight.

scrat

Question:

what does gyro_cmpf_factor and gyro_cmpfm_factor do? Thx.

scrat

I have 3 boards original rev5 with latest bf...all working usb connections every time on Mac and Win 8.1. Do you have the latest bf configurator and latest CP drivers installed?

scrat

Great...something new..and bf configurator is better and easier. And I see some new settings for GPS.

scrat

Anand wrote:The new Baseflight update now includes SBUS option, can i use a Frsky rx on the cppm plugs?

Also what is the common way to mount the naze32 mini in a quad? Velcro?

Nylon standoffs or double sided tape.

scrat

copterrichie wrote:IMO, it all comes down to how the main power-lines are routed.

and code and algorithm.

scrat

Did you calibrated esc's?

scrat

Just buy acro board.

scrat

uBlox center will not work on mac.

scrat

timecop wrote:I've already told you, i'm on the same reel of MPU6000s that I've had for several years.
(I did buy a new reel recently, but it's going to get wasted because I'm moving to MPU65 for any new hardware).

Sorry for offtopic...what is benefit of MPU6500 over MPU6000?

Thanks.

scrat

kilby wrote:
Unfortunately it is in the retarded American date format

+1

scrat

Rate aka ACRO mode? Because I've never had that kind of problem and I'm flying just acro mode.

scrat

Im looking at the raw sensor data tab right now. The X axis is showing a steady 0. The Y axis (which responds to pitch on my quad), is alternating quickly between -0.24 and 0. The Z axis is a steady -0.24. Does that sound about normal? 0.24 degree per second doesnt sound like it would cause problem...

scrat

Thanks man!

scrat

This code works on rev5?

scrat

I dont have a vibration problem. My problem appears identical to what Thorvald reported here: http://www.multiwii.com/forum/viewtopic.php?p=53330#p53330 and antix here: http://www.multiwii.com/forum/viewtopic.php?f=23&t=1947&start=900#p53402 The only difference is that upgrading the firmwar...

scrat

ezio wrote:
scrat wrote:Enable baseflight support in settings.
And for now please do not use the PID with naze32. It can set VEL to wrong values.

Thanks. About VEL...ask me how I know. Nothing broken...just alt hold doesn't work.

scrat

I did hear rumors 2.4 would be 2560 processors only. Ok for me, but i think its suicidal. -We need to fork a 328 / 32u4 version, maybe call it SimpleWii. -Throw out stuff nobody uses, like openlrs. -Go back to arduino ide. -Throw out alarms,lcd,log and other nonsense code. -Throw out code for senso...

scrat

ezio wrote:
msev wrote:Ezio, how good is baseflight compatibility in your app regarding pid tuning and cli? Works or not?

There are some problems with vel. I will try to fix it asap. Cli works.

When connected over BT to naze32 with baseflight...CLI disappears from second screen.

scrat

I saw his post. Interesting reading. So I'll stick to NEO 6 for now.

Search found 925 matches