MultiWii

Flying wing servo/motor assignment changed a bit, I just commited a patch to baseflight that *should* make motor + servos properly work, of course you'll need to build your own version to try it out. I think GUI now expects motor to be in servo[7], which is probably why you don't see it. Ok, thanks...

Did you ever come across the idea to arm the fc like described in mwii wiki? If that doesn't work, sell the board or buy a radio that reaches the appropiate stick limits if you are not able to change them in cli or your TX. Arming hasn't changed for "several months" in any mwii "univ...

I have been trying to set up a flying wing with Baseflight on my ver.4 board. I gotmost tings working, but can not arm the motor. Servo's are working and all seems fine, all but motor. Gui works, but somewhat unstable. In gui all rc/servo show's but not motor in "live rc", throttel indicat...

Hi I have been trying to set up a flying wing with SG2.5 on my ver.4 board. I gotmost tings working, but can not arm the motor. Servo's are working and all seems fine, all but motor. Baseflight2 gui works, but somewhat unstable. In gui all rc/servo show's but not motor in "live rc", thrott...

Joining

Pretty sure if you use PPM + camstab gimbal servos stay on 1/2 and then motors to 3,4,5,6 and then the other 2 go on the RC input header? The manual covers this. I got all that right, but was hoping that it could be a way to free 1 rc channel and keep the servo signal on the Naze32 ? Maby i'm just ...

Hi. I have a Hexa with a 2axis gimbal. I use PPM rx Fasst 8ch. When i stepped up from Quad to Hexa i lost 2 ch to the motor's. Does it have to be like this, or is there a way to free up ch 5-6 ? At the moment i have the servo's on two knobs for roll and tilt. I dont need both roll and tilt on separa...

Ok, got my rev4 Hexa working again after shorting Bootloader pins and global erase when flashing new baseflight.
Had an FPV-flight in gyro-mode an got brave over white snow surface.......

Result's :

Pow at the manual house to do the short cut. I don't understand what you meen ? I made a video of the led-issue. m never seen that and I can't really imagine how that can happen, either, so yeah as others said, reflash using bootloader pins, and make sure to 'erase all' in flash loader to make sure...

nicog wrote: Pow at the manual house to do the short cut.

I don't understand what you meen ?

I made a video of the led-issue.
http://youtu.be/mnMgHV7AR7Y

Hi
My rev4 board stopped responding, the green led are flashing/blinking strange.
It starts solid and ends with rapid flahing/blinking, no red led activity.
Cant connect with BT or usb to Cli or Mwii.
Any ideas.... ?

Wooohooo !

My new board is in the mail already... Thanks TC

A video of my Naze32 Hexa, ver.1
http://www.youtube.com/watch?v=nUUWTuUHmnc

Very stable in gyro mode, haven't tuned it much in Horizon mode.

Just ordered a ver.4 board

With r213, I have the Naze32 and my Eagle Tree V3 Logger/OSD Pro successfully sharing the same Eagle Tree GPS V4. The brown Tx line from the GPS is split and connects to pin 4 on the RC Header on the Naze. I set gps_type=0, gps_baudrate=38400 and feature gps (I had missed this last step before). Al...

I am trying to get my Eagle Tree v4 GPS working with my Naze32 under 213. My Naze32 is running PPM. I set gps_baudrate=38400 and gps_type=0. I am running Multiwii Gui 2.1. Which wires on the GPS did you use for TX and RX into the Naze (red, white, yellow, brown)? The pinout I found for the GPS cabl...

I believe gps speed shown is in cm/sec, and if you're expecting accurate speed values from a module that's not moving, well, ... Don't take it the wrong way TC, i was not expecting anything... I just tought it was funny that the quadd was moving realy fast . . . . . in the windowpost..... LOL At th...

MTK init sequences ARE sent with gps_type=2. I haven't tested if MTK3329 (that FMP04 module I got) accepts them or not, but according to the datasheet/protocol PDF, it should. gps_type=0 is for modules t hat do NOT need any external configuraion and you KNOW thier baudrate ahead of time - i.e. modu...