Search found 8 matches
- Fri Mar 01, 2013 11:37 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1450054
Re: Naze32 hardware discussion thread
Does it really cost more than $4 flat rate shipping to bumfucknowhere USA!!??
- Tue Oct 16, 2012 5:36 am
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1450054
Re: Naze32 hardware discussion thread
I had this when using the plush ESC's, erratic starting and speed on differant motors, set min throttle to 1200 (as per timecops advise) and solved the problem.
regards.
regards.
- Sat Sep 22, 2012 1:47 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1450054
Re: Naze32 hardware discussion thread
timecop wrote:you need feature telemetry on as well
Thanks TC,
Knew it would be something dumb.
David.
- Sat Sep 22, 2012 12:23 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1450054
Re: Naze32 hardware discussion thread
(posted @ rcg) If anyone else can help me out with this it would be appreciated, just need to know how the Frsky D4R-ll receiver can be hooked up to the board with telemetry adapter. There's pinout on the bottom of D4FR-II. RX/TX/GND/A2 or something similar. Wire up the frsky adapter as shown in th...
- Mon Sep 17, 2012 9:34 am
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1450054
Re: Naze32 hardware discussion thread
This gets more interesting. With either a DSM2 and DSMX satellite, it works perfectly if I turn on the FC board/Satellite first, followed by the TX. With the reverse power up sequence, it looks as if the satellite is not getting a valid signal. It, along with the TX must be powered down, and then t...
- Mon Sep 17, 2012 9:27 am
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1450054
Re: Naze32 hardware discussion thread
(posted @ rcg) If anyone else can help me out with this it would be appreciated, just need to know how the Frsky D4R-ll receiver can be hooked up to the board with telemetry adapter. There's pinout on the bottom of D4FR-II. RX/TX/GND/A2 or something similar. Wire up the frsky adapter as shown in th...
- Mon Sep 17, 2012 3:19 am
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1450054
Re: Naze32 hardware discussion thread
John, I had similiar problems with this when using 5volt supply. I ended up using the OP spektrum adaptor to supply 3.3?volts and from that point on has been 100% reliable. For whatever reason the higher voltage caused erratic behaviour. David. spektrum sat is a 3v device, I'm surprised it still wo...
- Sun Sep 16, 2012 11:42 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1450054
Re: Naze32 hardware discussion thread
Question for any Spektrum Satellite users: I can take a DSM2 satellite, and bind it to my TX, either with a receiver or via an Arduino sketch. I then hook it up to the Naze, powerup, and it works fine, once. At the next powerup, the Satellite goes back into bind mode. I've tried setting the GPIO in...