MultiWii

Hi to all, anyone can ask me why my home arrow was always wrong?? And see the Home distance, when was at 652m the counter restart to 0m, was normal? See the video: m I can ask you, why your home arrow always wrong ? :D:D Both simptoms are known errors and will be fixed in the upcoming release of i2...

Hi to all, anyone can ask me why my home arrow was always wrong?? And see the Home distance, when was at 652m the counter restart to 0m, was normal?

See the video:

http://www.youtube.com/watch?v=7x0MTfyN ... Sw&index=1

Hi to all, anyone can ask me why my home arrow was always wrong?? And see the Home distance, when was at 652m the counter restart to 0m, was normal? See the video: m Are you using I2C GPS? There is a known issue with arrow direction and the limit of 650 meters to home. If you search in the GPS inte...

Hi to all, anyone can ask me why my home arrow was always wrong?? And see the Home distance, when was at 652m the counter restart to 0m, was normal?

See the video:

http://www.youtube.com/watch?v=7x0MTfyN ... Sw&index=1

Hi, can anyone explain what are the correct modification on the CODE to have a better Drotek I2CGPS (MT3339 FW AXN2.10_5156_3339_1152.1101000.10) ? Thanks Video for explain: m Gps speed wrong and coordinates when GPS make the fix oscillate Gpd speed in multiwii gui 2.1 m Gps Tool 1.7.1 m SOLVED than...

Michal,

+ GPS speed units changed to km/h (tested by Neo360)

Not is my idea but was by CarlonB i just tested after i told him

Remember my request please RSSI in %

Please help me, there is no chance to reflash the firmware in case of bad flash? Now if i put the correct firmware i see always this message: [Flash Download] Fail!!(Download) BROM_CMD_START_FAIL [Finish] Take(6) secs to test. I try with the vcc trick but dont works. I try with flash tool 1.0.0 but ...

Help me please, how it can be possible to reflesh AXN firmware?

I see that my gps have axn 2.11 firmware and i try to flash the axn 1.51 but now dont works anythings even if the flash is successful!

Please help me.

I tried with flash tool 1.0.0 but dont save me

Alexinparis wrote:

Neo360 wrote:Now it's possible to use an Xbee Pro for telemetry?

yes absolutely

Nice. But sorry Alex i dont understand as i do!

Please you explain me the right metod?

P.s: i have the drotek flight ctrl with ATmega328p

Now it's possible to use an Xbee Pro for telemetry?

It's possible that anyone have information about that?!?

The xbee module are compatibile with multiwii?

Hi,

Can anyone know what is the correct parameter to set the module?

I try but dont works, the GUI start with loss packet and receive nothing.

For neo360, toggle your nema database to 0 (WGS1984 "international") and mayme your gps is in 5hz So parser lag and give bad coordonates I put a post in drotek forum about tunning the GPS of drotek. If you don't understand french, I can translate for you. when i put nema database to 0? pl...

Guys how can i put the new GPS code on the onboard atmega in my I2C GPS?

Hi,

I have this GPS http://www.drotek.fr/shop/en/88-i2c-pa6c-gps-llc.html

where is the right metod to upload the new code on the atmega on board?

http://code.google.com/p/i2c-gps-nav/downloads/list

I try with FTDI port but arduino get this error: avrdude: stk500_getsync () : not in sync resp=0x00

help me please

Hi Guys, Help me please, because i have one doubt!! I have the I2C GPS by Drotek with Drotek CTRL Flight RED edition, i dont understand why the GUI show me this coordinate (See the picture), i think that was not correct because my real coordinate was LAT 45.302542° LON 7.898999° we have any idea abo...

https://vimeo.com/47463547

Ok only my problem are solved i just used a NPN 2N2222A transistor

I try with my PNP transistor but dont flash always on.

Wiring:

Emiter to +BATT, Base via 2,2k resistor to port B4, Collector to LED+ and LED- to ground.

Hi, One think, what is the PB4 output on Mega328P? I have this board m Well, PB4 IS the pin identifier for the ATMega. It maps to digital pin 12 on an Atmega238p-based Arduino Duemilanove or Uno if that's what you mean. http://arduino.cc/hu/Hacking/PinMapping Ok i find the pb4 out. Another think i ...

I created a little patch to add an effective LED strobe to my copter. The LEDs are connected to PB4 (using a transistor as a switch), which is toggled by the software during the control loop. The flash sequence can be modified by setting the define LED_FLASHER_SEQUENCE or even at runtime by calling...

Hi guys, i nedd you for some things!!

I have this flight control http://www.drotek.fr/shop/en/72-multiwi ... c5883.html and i want use the output led onboard to use the led flasher function, but i dont say what is the correct parameter to make this.

Anyone help me please?

Thanks

This is what i want

http://www.youtube.com/watch?v=mYIIX7f1-yQ