MultiWii

Thank you for your answer. I found the problem , in case someone else will have the same I solved it I forgot to uncomment this: /******************************** ARM/DISARM *********************************/ /* optionally disable stick combinations to arm/disarm the motors. * In most cases one of t...

Hi , I recently upgraded from 2.2 to 2.3
Al sensors in gui seems fine but when I activate Horizon- Mag- Baro the quad become almost unresponsive. Is take off slowly and it is very very sluggish even if extreme sticks movement. Any idea?

Andrea

Hi I ugraded to 2.3 from 2.2 and now ( with all the same settings) I am unable to arm with sticks. My value for rc are thr 930 / 2020 pitch 927/2023 roll 930 / 2014 Yaw 930 / 2022 Mincommand 940 mintrhottle 1300 maxthrootle 1950 #define MINCHECK 1100 #define MAXCHECK 1900 Arm unchecked in gui Any id...

I saw a lot of gps that seems very similar to me , can you help me choosing the best / most compatible for multiwii ? http://www.ebay.com/itm/Crius-CN-06-Standalone-GPS-Receiver-v2-0-Module-S-/121224042701?pt=Radio_Control_Parts_Accessories&hash=item1c398418cd http://www.hobbyking.com/hobbyking/...

Yes calibrated.
I managed to make the motos arm using an old programm in my radio.
I am trying to figuring out why with the normal program didn't arm.
Thank you

Hi guys, Everything works perfect before I connected the flyduino mega to pc via bluetooth. Now I can see all parameter in hte GUI via FTDI or via Bluetooth , but I am no more able to upload sketch. I tried to disconnect everything leaving only ftdi , changing port, changing pc , nothing . The leds ...

Thnak you I'll try.

Hi I upgraded from 2.1 to 2.3. Same comment on config and deifne.h Seems to fly ok but I have a lot of i2c errors in 2.3 . Any idea? I am using a 10 dof from cgs eu instead a 9 dof and I have to change the ime settings in def accordingly Those are the changes I made in the code. CONFIG #define QUADX...

Hi guys , my mini quad act very stange. Motors don't spin togheter. ( range of commands in gui are all between 950 and 2000 , MAXTHROTTLE 1950 MINTHROTTLE 1150 MINCOMMAND 900) esc plush 6A Also when I arm the board the esc start slowly beep , but if I give throotle the starts . I made calibration fo...

Opss sorry , now pubblic

I had problem with a tricopter with multiwii 2.2 The tail servo is super sensitive and is shaking a lot , the tricopter is almost not flyable . I tried to change pid without results. Also the front motor make a very strange noise that stop if I take firmly the yaw mechanism , I double checked prop m...

HI guys My tricopter was ok till I decided to swap my kk for a multiwii system that was previously on my quad. The tail start swing even at ground and when I try to fly it is very difficult to control with pitch stick very unresponsive and with on / off like behavior. Default PID The tricopter flew ...

I am stuck , is anyone able to help me? MultiWii_2.1_r1129.cpp:2310:8: error: #if with no expression MultiWii_2.1_r1129.cpp: In function 'void blinkLED(uint8_t, uint8_t, uint8_t)': MultiWii_2.1_r1129.cpp:458: error: 'LEDPIN_TOGGLE' was not declared in this scope MultiWii_2.1_r1129.cpp: In function '...

thank you very much very clear explanation !!

Thank you very much for your kind replay!!!
Let me understand, if I angage alt hode in stady state, then I lift the copter and regain a steady state at higher altitude, the alt hold disengage during the change and angage itself another time when the trust level return in the neutral zone, is it right?

ilbiso@gmail.comHi guys , I have a IMU 10DOF ALLINONE IMU ITG3050 HMC5883L BMA180 MS5611 sensor board 5V LLC from csgshop there isn't this imu on config.h of multiwii 2.1 there is an ALLINONE imu 9d0f but with BMP085 instead of mine MS5611. with this setting the quad fly well only in acro and in sta...