Search found 10 matches
- Thu Nov 01, 2012 3:00 pm
- Forum: Ideas
- Topic: [idea] quick calculation for lpf setting
- Replies: 4
- Views: 2196
- Mon Oct 29, 2012 8:05 am
- Forum: Ideas
- Topic: [idea] quick calculation for lpf setting
- Replies: 4
- Views: 2196
Re: [idea] quick calculation for lpf setting
about sensor data log .. i tried to grad the raw data.. but it was not significant even i push throttle above hover point.. it jumps between +/-5... i was thinking if we can get more accurate log.. say 100x the raw data.. then the small number becomes significant... should add some accuracy on anal...
- Sun Oct 28, 2012 8:28 am
- Forum: Ideas
- Topic: [idea] quick calculation for lpf setting
- Replies: 4
- Views: 2196
Re: [idea] quick calculation for lpf setting
i'm trying to figure out which freq lpf is the best go with for best result. well balanced motor and props is the best way. like you, for my knowledge , i wondering about methods to measure frequencies. with motor KV, we can approximate RPM: ex=> 1200KV Lipo 3S => 1200 X 12.6=> 15.000 rpm => 250Hz ...
- Wed Oct 24, 2012 7:21 pm
- Forum: ESCs, propellers , servos and radios
- Topic: hk10a esc (261000002) in mini quad
- Replies: 2
- Views: 1689
Re: hk10a esc (261000002) in mini quad
hi,
i mounted them on mini quad, with turnigy 1810 -2900KV, flashed with latest simonk Firmware=> Great !
http://youtu.be/gPlhIh9IOkA
http://youtu.be/49kEZMlus88
i mounted them on mini quad, with turnigy 1810 -2900KV, flashed with latest simonk Firmware=> Great !
http://youtu.be/gPlhIh9IOkA
http://youtu.be/49kEZMlus88
- Sat Oct 20, 2012 9:53 pm
- Forum: Software development
- Topic: MultiWii EZ-GUI
- Replies: 1434
- Views: 744173
Re: MultiWii EZ-GUI
not ok for my HTC incredible S (4.0.4)
Aux checkbox are still empty, blank screen with title on top .
MW 2.1
Aux checkbox are still empty, blank screen with title on top .
MW 2.1
- Mon Oct 15, 2012 8:05 pm
- Forum: Software development
- Topic: MultiWii EZ-GUI
- Replies: 1434
- Views: 744173
Re: MultiWii EZ-GUI
Dellow wrote:Just checked again, and AUX switch check boxes are not showing for me, either on my crappy tablet or my Samsung Galaxy phone, so not sure what's wrong..
+1 on HTC incredible S.
In all case, your new layout is nice! Good job!
- Wed Oct 03, 2012 8:29 pm
- Forum: Shields, boards and sensors
- Topic: NEED HILP with connecting HK MultiWii V2.0 board
- Replies: 2
- Views: 1426
Re: NEED HILP with connecting HK MultiWii V2.0 board
See this post for connection diagram....
viewtopic.php?f=18&t=2439
viewtopic.php?f=18&t=2439
- Mon Sep 24, 2012 5:30 pm
- Forum: Software development
- Topic: MultiWii EZ-GUI
- Replies: 1434
- Views: 744173
Re: MultiWii AllinOne for Android [update 24/09/2012]
Just Perfect. IMO, no more to add
- Fri Sep 14, 2012 11:48 am
- Forum: Getting Started - MultiWii config and setup
- Topic: Pin A3 on Crius
- Replies: 2
- Views: 1910
Re: Pin A3 on Crius
Thanks Pat, My board is V1, the layout is different from your post. I just find a pic on RCG. i have my answer. i expected to find A3 pin already soldered with header pin ,and i didn't think to looking around see the picture below: http://www.photo-worx.de/content/mikrokopter/CriusSEupgraded_Pinouts...
- Thu Sep 13, 2012 6:24 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Pin A3 on Crius
- Replies: 2
- Views: 1910
Pin A3 on Crius
hi all,
i got a Crius SE and i would like to connnect voltage divider for lipo monitoring .
But where is the pin named A3? crius has A0, A1 and A3
Thanks for your help.
i got a Crius SE and i would like to connnect voltage divider for lipo monitoring .
But where is the pin named A3? crius has A0, A1 and A3
Thanks for your help.