Search found 22 matches
- Sat Mar 02, 2013 12:22 am
- Forum: Software development
- Topic: KV Team Multiwii OSD
- Replies: 1021
- Views: 389921
Re: SW Development on Minim Osd
Well I think the team has done an excellent job, can't wait to try it, very nice!
- Thu Feb 28, 2013 2:20 pm
- Forum: Software development
- Topic: Release 2.2 is coming
- Replies: 167
- Views: 56474
Re: Release 2.2 is coming
Thanks for the info guys, think it was a case of to late at night and not reading thing through properly!
Thanks for the replies.
Shane
Thanks for the replies.
Shane
- Thu Feb 28, 2013 2:10 am
- Forum: Software development
- Topic: Release 2.2 is coming
- Replies: 167
- Views: 56474
Re: Release 2.2 is coming
DOH! ok its my fault!
all sorted
thanks
Shane
all sorted
thanks
Shane
- Thu Feb 28, 2013 2:00 am
- Forum: Software development
- Topic: Release 2.2 is coming
- Replies: 167
- Views: 56474
Re: Release 2.2 is coming
Hi all, just tried to fine tune the voltage display using the following #define VBATSCALE 131 // (*) change this value if readed Battery voltage is different than real voltage is this the right thing to adjust? if so it does not make any difference to my voltage reading, went from 131 to 100 it stay...
- Mon Feb 25, 2013 11:45 am
- Forum: Software development
- Topic: KV Team Multiwii OSD
- Replies: 1021
- Views: 389921
Re: SW Development on Minim Osd
Hi, Crius AIO Pro, MW 2.2 pre. GPS all works, it's just the little arrow for pos hold that does not show on mine, RTH shows fine. And is it actually engaged? that sounds very strange to me... Verify on your MW GUI please, you have the same board then the ones I use so, no doubt that it should be OK...
- Mon Feb 25, 2013 12:35 am
- Forum: Software development
- Topic: KV Team Multiwii OSD
- Replies: 1021
- Views: 389921
Re: SW Development on Minim Osd
kataventos wrote:Hi,
Question: The ones who are having problems with GPS mode, are you using I2C GPS ?
KV
Edit: And what MW version?
Hi, Crius AIO Pro, MW 2.2 pre.
GPS all works, it's just the little arrow for pos hold that does not show on mine, RTH shows fine.
- Sun Feb 24, 2013 1:46 pm
- Forum: Software development
- Topic: KV Team Multiwii OSD
- Replies: 1021
- Views: 389921
Re: AW: SW Development on Minim Osd
Hi, I get the little arrow marker for GPS RTH but not for GPS position hold, all other arrows acc, bar, mag are ok
- Sun Feb 24, 2013 11:58 am
- Forum: Software development
- Topic: Super simple gimbal improvement
- Replies: 15
- Views: 8626
Re: Super simple gimbal improvement
I loaded 2.2 last night and setup config.h like I have before... and my gimbal went crazy. I could not get it to react to frame movement at all. Eventually, the gimbal stopped working all together and now the servo's don't even budge when I power the board. Sure hope I didn't fry my servo's I am ab...
- Sat Feb 23, 2013 11:22 am
- Forum: Software development
- Topic: KV Team Multiwii OSD
- Replies: 1021
- Views: 389921
Re: AW: SW Development on Minim Osd
That's the one I'm using too. But when I am using the GUI to change some things being displayed or not and hit write nothing happens...e.g. If I hit read everything is default again. How did you configure your minimosd? Maybe I uncommented or did something wrong though I did just follow the wiki......
- Sat Feb 23, 2013 1:57 am
- Forum: Software development
- Topic: Multiwii dev 1317 and 1342 cam stab problems
- Replies: 4
- Views: 1806
Re: Multiwii dev 1317 and 1342 cam stab problems
Hi, found where to put the code, all working again!
thanks
Shane
thanks
Shane
- Sat Feb 23, 2013 1:49 am
- Forum: Software development
- Topic: KV Team Multiwii OSD
- Replies: 1021
- Views: 389921
Re: SW Development on Minim Osd
Hi all, I'm using these http://www.goodluckbuy.com/on-screen-display-osd-board-minimosd-apm-telemetry-to-apm-1-and-apm-2.html
with no prob's at all!
thanks
Shane
with no prob's at all!
thanks
Shane
- Sat Feb 23, 2013 12:57 am
- Forum: Software development
- Topic: Multiwii dev 1317 and 1342 cam stab problems
- Replies: 4
- Views: 1806
Re: Multiwii dev 1317 and 1342 cam stab problems
Hi, SERVO_MIX_TILT does not work on 2.2 pre, running on r1342 with this code mod to super simple #ifdef SERVO_MIX_TILT // Simple CameraGimbal By Bledy http://youtu.be/zKGr6iR54vM if (rcOptions[BOXCAMSTAB]) { #define LOWPASSFILTER(OLDVALUE,VALUE,FILTER) ((VALUE*(8-FILTER)+OLDVALUE*FILTER)/8) #define ...
- Sun Feb 17, 2013 12:01 pm
- Forum: Software development
- Topic: KV Team Multiwii OSD
- Replies: 1021
- Views: 389921
Re: SW Development on Minim Osd
Hi all, just like to say thanks to all the team (sorry to here about the drop outs!) for the time and effort put into this project.
Looking good and running smooth! can't wait to give it a go (still building the ground station!) but with this up front I'm sure it's going to be fun.
Thanks again
Shane
Looking good and running smooth! can't wait to give it a go (still building the ground station!) but with this up front I'm sure it's going to be fun.
Thanks again
Shane
- Tue Nov 27, 2012 11:48 am
- Forum: Shields, boards and sensors
- Topic: I2C OLED thread
- Replies: 62
- Views: 58817
Re: I2C OLED thread
I have two crius oled (co-16) and have the same problem with both. Random dots at startup unless it is connecetd after full initialisation of the oled. Could it be a problem with the init sequence? Hi, I have 2 of these screens and both give me the dots randomly on FC Boot. Tried connecting after a...
- Thu Nov 22, 2012 3:31 pm
- Forum: Software development
- Topic: New RCtimer GPS Ublox Neo 6M fails to perform on Mega boards
- Replies: 152
- Views: 105073
Re: New RCtimer GPS Ublox Neo 6M fails to perform on Mega bo
nice to hear that, with smaller one I've never got fixex in house . But I think what we need is the stable signal outside, when flying far and high, that's important. I sometimes loose the signal without any reason, it's very dangerous. Hi, I have 2 of the smaller Ublox neo 6 modules, the first 1 I...
- Wed Nov 14, 2012 12:32 am
- Forum: Software development
- Topic: r1240 roll of death
- Replies: 10
- Views: 3576
Re: r1240 roll of death
I run ALL ESC's +5V together, no external BEC on any. The ESC's are all turnigy plush on all craft.
- Thu Nov 08, 2012 8:41 pm
- Forum: Software development
- Topic: r1240 roll of death
- Replies: 10
- Views: 3576
Re: r1240 roll of death
Hi scrat,
Yes I am using r1240 on the Crius AIO Pro running well no prob's as yet, and had about 7 to 8 flights of 10 mins.
Yes I am using r1240 on the Crius AIO Pro running well no prob's as yet, and had about 7 to 8 flights of 10 mins.
- Fri Sep 07, 2012 10:40 am
- Forum: Software development
- Topic: New RCtimer GPS Ublox Neo 6M fails to perform on Mega boards
- Replies: 152
- Views: 105073
- Tue Aug 07, 2012 4:10 pm
- Forum: Software development
- Topic: New RCtimer GPS Ublox Neo 6M fails to perform on Mega boards
- Replies: 152
- Views: 105073
Re: New RCtimer GPS Ublox Neo 6M fails to perform on Mega bo
Don't think it's that because I had it on the bench GPS running for ten mins and an 8 sat lock, plugged in the flight pack with it still on the pc the ESC's start to beep but don't finish? the board arms and disarms and the GPS LED's are flashing but the ESC's just don't give the final init tone? tr...
- Tue Aug 07, 2012 11:09 am
- Forum: Software development
- Topic: New RCtimer GPS Ublox Neo 6M fails to perform on Mega boards
- Replies: 152
- Views: 105073
Re: New RCtimer GPS Ublox Neo 6M fails to perform on Mega bo
Hi All,I have a strange problem, been running multiwii v2.1 with the Neo 6 at 115K with no problems (apart from the power cycling and the odd config refresh) So I thought I would give the following a go(bottom of page). I loaded all the bits in with the new gps.ino, compiled and had the missing endi...
- Tue Jul 24, 2012 9:59 am
- Forum: Software development
- Topic: Once again about MAG
- Replies: 21
- Views: 9204
Re: Once again about MAG
Hi Ainadiel
I have the file you need, if you have not got it yet let me know how to get it to you.
Woppit
I have the file you need, if you have not got it yet let me know how to get it to you.
Woppit
- Sun Jul 22, 2012 8:42 pm
- Forum: Software development
- Topic: Once again about MAG
- Replies: 21
- Views: 9204
Re: Once again about MAG
Hi all, and thanks to all those developing this fantastic software. I have been running Multiwii from v2.0 (now on v2.1) on 2 crius se boards, 1 on a quad and the other on a Y6 with no problems. I have just upgraded the Y6 to a Crius AIO board (for GPS use) and all is rock solid except the mag headi...