MultiWii

Deet

You don't connect the pusher ESCs to the FC at all, you just run the ESC off the receiver channel the FC wont care what you are doing unless you are in POS_HOLD It is that simple, no code required, it will work A friend has used this method with several different flight controllers, only exception i...

Deet

just run it off a spare RX channel with a mix off your radio

Deet

Deet

sounds like brown out, add the cap as mentioned above

Deet

fnurgel, you shouldn't need to compile the GUI, it just runs under java

Deet

You need to ask the KV Team that question

Deet

GUI based OSD editor is in current version

Deet

what board type do you have selected?

Deet

What GPS do you suggest for the stand-alone version?

Deet

Are you sure you have the correct GUI version. The GUI has to match the sketch version. Not being able to WRITE is one of the issues you will see with a version mismatch

Deet

IF you are switching cell counts all the time, why not just monitor cell1 via the balance ports on whatever lipo you use, then your alarms are based on the same voltage all the time, and you get used to looking for the same voltages no matter pack size I know heli guys who do this between various ai...

Deet

All sorted I was using AUX4 as the OSD switch channel, so once I set #define OSD_SWITCH_3WAY 7 it worked perfectly (its logical channel not physical channel) The Screen editor works nicely, Once I get to do some test flights the next thing I want to test is if my "saved" screens copy onto ...

Deet

Loaded and looking good so far, really like teh layout editor One thing thats unclear is the 3 position OSD switch, is there a trick to getting this enabled? I assumed the centre would turn the OSD off, but that doesn't appear to be the case, I get the two selected views at hi and low, but mid posit...

Deet

Will load it later today and let you know any issues I find Shikra

Deet

Will load it later today and let you know any issues I find Shikra

Deet

1095, 1500, 1905 are the radio settings you need

Deet

Sorry if this has been covered

I have tried to instal WinGui on a MAC using Parallels and windows XP, but it just won't run

Has anyone had any success? Is it XP that might be the issue?

Deet

you can make your own, the parts list, schematic and the PCB design are all available form the ghettostation download site

Deet

I am having an issue, two actually... the first being flickering text, and the second being gibberish display... both are displayed in the video posted below... I apologize if these issues have been discussed before, but I haven't been able to turn up anything useful from searches.. probably wordin...

Deet

Yes, thats what I am doing there is details on the ghettostation wiki Do you have a link. I can't find any information. Have you managed to do it? I'm would like to use the naze32 full flight controller with ublox GPS. How do I get the telemetry data on the UAV to the audio in on the Vtx and then h...

Deet

The PAL jumper is redundant

Deet

have you got the gui version that matches the sketch version?

Deet

Yes, thats what I am doing

there is details on the ghettostation wiki

Deet

I have done some testing and worked out my issue is due to the ghettoproxy not polling the MW board The MW board I have has activity lights for the serial port. If I connect a BT module to that port and connect to the BT, the serial lights show activity. With the ghettoproxy connected to the serial ...

Deet

YES LTM is set, at 2400 baud at both ends I get a message saying P:LTM No GPS, 0 Sats, NO 3D FIX. If I disconnect the data between the ghettoproxy and the modem that changes to "no telemetry" So the Link from proxy to station is working, I just cannot seem to get the data from the FC to th...

Deet

I can't seem to get any data from my board running v2.3 into the ghettoproxy

i have tried different board rates, different pole settings, and swapped rx/tx leads on ech different config but just can't get data

Deet

It works fine on PPM

Deet

I posted about this earlier this year

It doesn't matter if MAG is selected to not, the yaw hunts as it it is trying to maintain a fixed heading.

In fast forward flight you don't notice the issue, but any kind of hover, or trying to yaw in slow flight, the board seems to fight you

Deet

I am seeing the same thing, I am having to fight the Yaw as if MAG is selected, even when MAG isn't.

IF I unplug the MAG sensor I don't get the issue

Deet

measure the hover current, set that number into OSD, done

Deet

Question regarding the software current emulation. Has anyone actually used it in real world. Interested to know results. How does it calibrate? Obviously you need an external current sensor hooked up to measure the current. Do you configure the current at 10%-20%-30%-etc-etc ? or do you only calib...

Deet

seriously, don't do it

bluetooth range is very short and unreliable

Deet

The ten seconds is the delay until the mag_cal starts, you then have 30 seconds to do the mag_cal

I can't see why you would want it to be longer

Deet

dman. reverse the Rx and Tx pins on the serial port and try that

Deet

Use a 12V reg off the 4S lipo to power all your video stuff, thats what I do

It will be an earthing issue, you can leave the GND solder bridge on the OSD board linked, that may help

Deet

ACC used to be Angle, my guess is you had the wrong GUI version

Deet

Angle is there in V2.3

Deet

just do it as radio settings Assuming you radio is capable of storing failsafe to all channels (some only do throttle) The store the following as your radio failsafe Roll/Pitch/Yaw, to Centre Throttle to Centre And you AUX channel that selects RTH to that position Just make sure that you have BARO a...

Deet

just do it as radio settings Assuming you radio is capable of storing failsafe to all channels (some only do throttle) The store the following as your radio failsafe Roll/Pitch/Yaw, to Centre Throttle to Centre And you AUX channel that selects RTH to that position Just make sure that you have BARO a...

Deet

select ANGLE whenever you are in a GPS mode

Deet

A question on the next version

Currently in r370, the flight mode indicator doesn't differentiate between ANGLE and HORIZON, it shows both as ACC

Will the next version be able to display them as different modes, EzyGUI can do so, so I am guessing its in the MSP somewhere

Deet

Just found a problem with r370 that may not be apparent to some users

If you set for displayGSP coords and you have a 3 digit longitude then the OSD will lock up as soon as you get a sat lock

Deet

comment the moving average gyro stuff

and set servo to 50Hz

then try again

Deet

define_servo_tilt_mix does that for you

Deet

Are there new servo diagrams available?

Deet

DJI do it… they have an iPhone App

Deet

Further update

I can get the cyclic servos to work fine with V2.2

Its the latest version of V2.3 I can't get to work. No matter what I try the Nick servo just stays at minimum. The GUI does show the output changing

Deet

I also tried servo[1] = servo[3]; with the nick servo into A1 and got the same result

I also tried PASSTHRU and the nick servo just stays at its low point and doesn't move no matter what I do with the radio sticks

Deet

Hi Deet. In def.h Find #elif defined(HELICOPTER) #define PRI_SERVO_FROM 4 Change to PRI_SERVO_FROM 1 Then you will have all available servooutputs enabled. Ok tried that, now the nick servo drives all the way to the lower end of travel and stays there I then commented the line I added and changed t...

Deet

Hi All I am stuck I am trying to set up a heli with a 32u4 controller I am using the latest release code. on 120 degree cclm I can't get the Nick servo to work. Because of the board I need to use output A0 for the nick servo I added "SERVO[0] =SERVO[3} to the end of the 120 CCPM helicopter sect...

Search found 129 matches