yes please check your PM for details
thanks!
Search found 17 matches
- Wed Jul 25, 2012 8:21 am
- Forum: Software development
- Topic: Once again about MAG
- Replies: 21
- Views: 9347
- Tue Jul 24, 2012 12:11 am
- Forum: Software development
- Topic: Once again about MAG
- Replies: 21
- Views: 9347
Re: Once again about MAG
hmmm i Moved esc outside the box, move sensor board as high as i can... and i run test... i connect hex6x to gui and without props i took some readings... even on full throttle mag was giving me the same values as on min throttle... so i am assuming that in my case magnetic field does not corrupt re...
- Sun Jul 22, 2012 12:11 am
- Forum: Software development
- Topic: Once again about MAG
- Replies: 21
- Views: 9347
Re: Once again about MAG
Not sure how you want to place that on your quad... i was thinking about using ferrite beads ( http://www.maplin.co.uk/ferrite-rings-and-beads-32792 ).
thought that i can place one of them between each motor and esc... gonna buy some of them next week and see if that would help...
thought that i can place one of them between each motor and esc... gonna buy some of them next week and see if that would help...
- Thu Jul 19, 2012 9:34 pm
- Forum: Software development
- Topic: Once again about MAG
- Replies: 21
- Views: 9347
Re: Once again about MAG
seems like your solution works for my hex6... thx
also i rebuild electronics and screen all/most of the cables... hex6 is keeping direction event during the wind - now just adjust PIDs and can go for long flight...
also i rebuild electronics and screen all/most of the cables... hex6 is keeping direction event during the wind - now just adjust PIDs and can go for long flight...
- Tue Jul 17, 2012 10:51 pm
- Forum: Software development
- Topic: Once again about MAG
- Replies: 21
- Views: 9347
Re: Once again about MAG
see mine is yawing to left... but just to check it i changed axis orientation for MAG only (I replaced #define MAG_ORIENTATION(X, Y, Z) {magADC[ROLL] = X; magADC[PITCH] = Y; magADC[YAW] = -Z;} with #define MAG_ORIENTATION(X, Y, Z) {magADC[ROLL] = -Y; magADC[PITCH] = X; magADC[YAW] = Z;} ) and i play...
- Tue Jul 17, 2012 10:36 am
- Forum: Software development
- Topic: Once again about MAG
- Replies: 21
- Views: 9347
Re: Once again about MAG
well i think that must be the problem than, especially that all my electronics including esc are closed in plastic square box... esc are in about 30mm from my sensor board... ( m ) but what is interesting i had the same set up before with my quad and everything was working fine! i see if once i rebu...
- Mon Jul 16, 2012 6:12 pm
- Forum: Software development
- Topic: Once again about MAG
- Replies: 21
- Views: 9347
Re: Once again about MAG
in my case when MAG is off it seems to be fine... when i switch MAG on it starts yawing to left. stops after (about) 90 degrees... after another test i crashed and broke my landing gear... i had similar problem with mag in my quad but then the declination was corrupted... latest version before 2.1 r...
- Mon Jul 16, 2012 3:45 pm
- Forum: Software development
- Topic: Once again about MAG
- Replies: 21
- Views: 9347
Once again about MAG
Hi there. I am using newest 2.1 multiwii for my HEX and for some reason when i am taking off and sometimes during the flight HEX is yawing to left... i am not sure if it is something wrong with soft or my hex because this board (DOF10) was working fine in my quad before... I was applying the same pr...
- Sun Jul 15, 2012 1:47 pm
- Forum: Pictures & Videos
- Topic: Heavy Lift Hexacopter -Flight Time-Weight-Details
- Replies: 6
- Views: 3639
Re: Heavy Lift Hexacopter -Flight Time-Weight-Details
i wonder at what throttle position your hex is taking off? the one i just build is taking off in about 55% of the throttle using 2x 2200mah batteries in parallel.
- Tue Jul 10, 2012 11:06 pm
- Forum: Software development
- Topic: Let's try to release 2.1: second try based on r964
- Replies: 65
- Views: 24784
Re: Let's try to release 2.1: second try based on r964
I got today a very interesting new Crius Board: m (ATMega 2560 ·MPU6050 ·HMC5883L ·MS5611-01BA01 ·FT232RQ USB-UART chip and Micro USB receptacle) It wold be a fine if anyone could add the IMU Code from the manual into the new release 2.1 m agree, please add this code to v2.1 by the way i really lik...
- Tue Jul 10, 2012 10:36 pm
- Forum: Pictures & Videos
- Topic: GPS RTH enabled MultiWii Hexa :)
- Replies: 12
- Views: 6109
Re: GPS RTH enabled MultiWii Hexa :)
hmmm now i need to figure out how
thanks for info!!!
thanks for info!!!
- Tue Jul 10, 2012 3:38 pm
- Forum: Pictures & Videos
- Topic: GPS RTH enabled MultiWii Hexa :)
- Replies: 12
- Views: 6109
Re: GPS RTH enabled MultiWii Hexa :)
so ia am now just wondering if by using flyduino pro mini i can make hexx with camera stabilisation or not?
- Mon Jul 09, 2012 9:16 pm
- Forum: Pictures & Videos
- Topic: GPS RTH enabled MultiWii Hexa :)
- Replies: 12
- Views: 6109
Re: GPS RTH enabled MultiWii Hexa :)
is this the same code that is going to be in multiwii 2.1?
Looks pretty awesome!
i am going to rebuild my quad for hex...
Looks pretty awesome!
i am going to rebuild my quad for hex...
- Thu Jun 14, 2012 7:22 pm
- Forum: Software development
- Topic: Magnetometer HMC5883 Glitching
- Replies: 22
- Views: 7323
Re: Magnetometer HMC5883 Glitching
i have the same board and on dev20120526 i had some problems, if i yaw quad it was loosing orientation... sometimes launched from hand it was doing 360degress and stop in position... now i have latest dev and seems like this problem disappear but i am actually still thinking about sending it back, g...
- Thu Jun 14, 2012 7:07 pm
- Forum: Software development
- Topic: GUI works very slow
- Replies: 13
- Views: 5022
Re: GUI works very slow
now im not sure if its my FTDI cable or what... seems like sometimes is faster and sometimes slower... i can go with slower gui as long as mag works ok... almost lost my quad because of previous dev when it start rotating like UFO...
- Thu Jun 14, 2012 5:58 pm
- Forum: Software development
- Topic: GUI works very slow
- Replies: 13
- Views: 5022
Re: GUI works very slow
i'm using USB connection to communicate with quad, processing application and I have Windows 7 64bit... however have to say that 64bit processing app does not work so I have to use 32bit... (it didnt work in previous devs as well) what is strange that one of my mates has exactly the same system and ...
- Thu Jun 14, 2012 5:24 pm
- Forum: Software development
- Topic: GUI works very slow
- Replies: 13
- Views: 5022
GUI works very slow
Hi there,
I am using newest dev and for some reason it works very slow... seems like it does not refresh in real time.
But on my mates laptop it works fine so I think problem lies in my laptop but i have no idea why.
Do you have any suggestions how to fix it?
Cheers!
I am using newest dev and for some reason it works very slow... seems like it does not refresh in real time.
But on my mates laptop it works fine so I think problem lies in my laptop but i have no idea why.
Do you have any suggestions how to fix it?
Cheers!