Search found 44 matches
- Wed Dec 11, 2013 1:21 pm
- Forum: Shields, boards and sensors
- Topic: Atto Pilot Voltage and Current Sensor- Reverse Current
- Replies: 1
- Views: 1109
Atto Pilot Voltage and Current Sensor- Reverse Current
Hi- I used an Atto Sensor with Simon K regenerative breaking FW- it failed. I guess due to back current generated, giving a negative input for the sensor? Any idea how to protect the Atto Sensor against reverse current to the battery? I guess a simple antiparalell Shottky won´t do due to the delta U...
- Thu Jun 27, 2013 6:26 pm
- Forum: Shields, boards and sensors
- Topic: GPS in MultiWiiConf
- Replies: 1
- Views: 1117
GPS in MultiWiiConf
Hi- debugging is a little hard without knowing the following: - in the GUI the grey Compass ring is blinking- fine but what does it mean EXACTLY? a) GPS is connected via I2C and the are talking "something" b) the Multiwii receives "some" GPS packets c) the Multiwii receives the c...
- Tue May 07, 2013 4:58 pm
- Forum: Software development
- Topic: SOLVED: Pitch and Roll gone PLEASE help, VERY odd!!!
- Replies: 6
- Views: 3327
Re: SOLVED: Pitch and Roll gone PLEASE help, VERY odd!!!
Thanks for the help of all- actually it was related to a bug I had ALL TIME... In the version of the MultiWii GUI I use (and love btw.) the parameters are not always transmitted correctly via the 3DR modules. Due to this the RC Rate RC Expo sometimes showed 0 even though (obviously) they had a usefu...
- Tue May 07, 2013 2:42 pm
- Forum: Software development
- Topic: SOLVED: Pitch and Roll gone PLEASE help, VERY odd!!!
- Replies: 6
- Views: 3327
Re: Pitch and Roll gone PLEASE help, VERY odd!!!
Hi- Sorry if the topic is wrong but I for sure have no idea what the cause might be and due to the behavior I described I do not think it is hardware . I use a FrSky receiver (D4R II with firmware upgrade for 8Ch to be exact) connected via PPM Sum. Fail save is disabled (in MultiWii) and independent...
- Tue May 07, 2013 1:50 pm
- Forum: Shields, boards and sensors
- Topic: I2C OLED thread
- Replies: 62
- Views: 61478
Re: I2C OLED thread
Awesome-
great idea- just put a mix on a unused switch and assign a stick combo- this way I will not use an extra channel!
Perhaps program it that way that the mix is disabled as soon as there is throttle input also- otherwise one also could name it the "flip switch"
Thanks!
great idea- just put a mix on a unused switch and assign a stick combo- this way I will not use an extra channel!
Perhaps program it that way that the mix is disabled as soon as there is throttle input also- otherwise one also could name it the "flip switch"
Thanks!
- Tue May 07, 2013 1:37 pm
- Forum: Software development
- Topic: SOLVED: Pitch and Roll gone PLEASE help, VERY odd!!!
- Replies: 6
- Views: 3327
Re: Pitch and Roll gone PLEASE help, VERY odd!!!
Thank you for this suggestion.
I went back to a config.h that has worked for sure before. Independent of this I never had failsave enabled so far... Also GPS PH or RTH is not activated- and even if so it still should react on stick inputs...
Greets
I went back to a config.h that has worked for sure before. Independent of this I never had failsave enabled so far... Also GPS PH or RTH is not activated- and even if so it still should react on stick inputs...
Greets
- Tue May 07, 2013 1:18 pm
- Forum: Software development
- Topic: SOLVED: Pitch and Roll gone PLEASE help, VERY odd!!!
- Replies: 6
- Views: 3327
SOLVED: Pitch and Roll gone PLEASE help, VERY odd!!!
Hi- on my X8 (Crius AIO Pro, Crius V2 GPS, 3DR telemtry, FrSky via PPM Sum, MultiWii 2.2) I wanted to use an Oled (Crius), too for GPS status info. I installed it and changed the code accordingly. Doing the testflight I found Pitch and Roll not working any more (Angle mode always on with this copter...
- Tue May 07, 2013 12:28 pm
- Forum: Shields, boards and sensors
- Topic: I2C OLED thread
- Replies: 62
- Views: 61478
Re: I2C OLED thread
With the CRIUS Oled I have that startup problem only when using fully charged 4s Lipo (Crius AIO Pro V2) odd... What ever- is there a way to start showing the telemetry pages WITHOUT any stick input? I have limited my stick values to 80%, so I am not able to activate it via remote without changing t...
- Sat May 04, 2013 9:21 pm
- Forum: Ideas
- Topic: Vib Test version
- Replies: 38
- Views: 27721
X8 odd mixing? Vib Test version
Hi- awesome SW, but I have a problem here- using it (the one by PatrikE » Thu Mar 28, 2013 9:08 pm I put together a version of v2.2. Dyn_Balanceing.zip) on a Crius AIO Pro motor M7 is almost always on, motor M6 can not be armed at all (copter works flawless with 2.2 , GPS and telemetry) Would be gre...
- Wed May 01, 2013 5:25 pm
- Forum: Software development
- Topic: What makes Naza 'better' than Multiwii
- Replies: 83
- Views: 31809
Re: What makes Naza 'better' than Multiwii
All my copters (Y6, X8, Quads) fly well with standard PID settings. I understand you concerns when it comes to changing PIDs for optimizing this or that characteristic but I would guess something else is wrong with your setup..
Did you try to use the low pass filtering?
Did you try to use the low pass filtering?
- Tue Apr 16, 2013 12:43 pm
- Forum: General discussions
- Topic: Flying (and AV AP) in Poland
- Replies: 0
- Views: 768
Flying (and AV AP) in Poland
Hi- I will make a trip to Poland soon and would like to do some airial shots for my homepage. Does anybody know what the regulations are in this country? Due to "sort of publishing" pictures / videos I d rather know how the regulations are exactly. Further more always better to know just i...
- Thu Apr 11, 2013 7:59 pm
- Forum: General discussions
- Topic: Solved: Multiplex equilibrium DX charger manual
- Replies: 4
- Views: 1805
Re: Multiplex equilibrium DX charger manual
Hi-
yeah- THIS charger has the possibility to set charging current independent of the capacity- nice if you KNOW HOW!!!!!!!!!!!!!!
Greets
yeah- THIS charger has the possibility to set charging current independent of the capacity- nice if you KNOW HOW!!!!!!!!!!!!!!
Greets
- Thu Apr 11, 2013 12:32 pm
- Forum: General discussions
- Topic: Flight data recording
- Replies: 35
- Views: 10376
Re: Flight data recording
This board seems to have lots of on board flash memory: http://www.rctimer.com/index.php?gOo=go ... oodsid=765
Perhaps this might help?
Perhaps this might help?
- Thu Apr 11, 2013 12:25 pm
- Forum: General discussions
- Topic: Solved: Multiplex equilibrium DX charger manual
- Replies: 4
- Views: 1805
Re: Multiplex equilibrium DX charger manual
Hi-
thanks a lot for your effort- but it does not help with my type of charger- the Equilibrium DX...
Obviously I tried google already without success, so help here would be great!
Greets
thanks a lot for your effort- but it does not help with my type of charger- the Equilibrium DX...
Obviously I tried google already without success, so help here would be great!
Greets
- Wed Apr 10, 2013 9:05 pm
- Forum: Shields, boards and sensors
- Topic: CRIUS all in one V2.0 Some help please
- Replies: 2
- Views: 1480
Re: CRIUS all in one V2.0 Some help please
Hi- This is a Multiwii forum- I guess you will have more luck with your question somewhere else. Anyways- I have tried to use Megapirate NG also and it was not working for me, too (other problem though). Now I use Multiwii on all my copters and think it is really nice and developing fast. Good luck ...
- Wed Apr 10, 2013 7:08 pm
- Forum: General discussions
- Topic: Solved: Multiplex equilibrium DX charger manual
- Replies: 4
- Views: 1805
Solved: Multiplex equilibrium DX charger manual
Hi- I need to change the charging current- BUT HOW... Lost my manual- everything else is pretty straight forward but i do not get to the point where I can change the charging current... I can set the capacity to the correct value but the current selection was somewhere else.... Could somebody please...
- Wed Apr 10, 2013 1:47 pm
- Forum: Ideas
- Topic: Vib Test version
- Replies: 38
- Views: 27721
Re: Vib Test version
Hello- sorry for this question but will Ihave to disconnect all +5V wires from the ESCs then? Or use a special USB cable with a cut 5V line? I would expect to fry the USB port when I connect my FC to the PC and connect the Lipos to power the motors at the same time (CRIUS AIO Pro without external BE...
- Fri Mar 29, 2013 6:12 pm
- Forum: Links
- Topic: Ready- made and tested Multiwii drones
- Replies: 3
- Views: 4501
Re: Ready- made and tested Multiwii drones
I also paid less then 50 Us$ for the "training quad"- including shipping to Germany!!!!! (Not in the advertised store obviously)
- Thu Mar 28, 2013 1:57 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Y6 X8 Mixer table: how to add 10% RPM
- Replies: 2
- Views: 1439
Y6 X8 Mixer table: how to add 10% RPM
Hello- I would love to have the lower prop level in an y6 or x8 configuration rotating faster (about 10%) to get a better efficiency. I already had a look at the mixing table (MW 2.2). It makes sense to me but I am not absolutely sure how to add the needed 10% code wise. Would be great if somebody c...
- Fri Mar 15, 2013 11:24 am
- Forum: Software development
- Topic: 2.2 Gui working with 433 Mhz 3DR modules
- Replies: 2
- Views: 1695
2.2 with 3DR 433 Mhz telemetry: works
Due to the efforts of EOSBandi and all the programmers working on 2.2 it seems the new GUI works great with 2.2 via 433 Mhz, too. My setup: - CRIUS AIO Pro FC - CRIUS V2 GPS - 3DR 433 Mhz Modules (configuring them is pretty easy with the Megapirate SW) - WinGUI2_2betaR37 via USB 3DR module set to 57...
- Thu Mar 14, 2013 11:58 am
- Forum: Software development
- Topic: 2.2 Gui working with 433 Mhz 3DR modules
- Replies: 2
- Views: 1695
2.2 Gui working with 433 Mhz 3DR modules
Dear all- due to the wish to connect my 3DR modules to do the tuning of PIDs the "nice way" I would need to change the GUI settings to 57600baud.. The MultiWiiWinGUI did support this change but it seems not to work with 2.2 (as could be expected I guess)- any way to change it in the MultiW...
- Thu Mar 14, 2013 11:51 am
- Forum: Software development
- Topic: 2.2 twitches while flying
- Replies: 20
- Views: 7815
Re: 2.2 twitches while flying
Awesome-
when I saw this setting I knew I v see it before- it even says "twitching" in the comment... I only did not see the relation because I never had problems with this before.
Anyways- it works now- thanks. Still is a little nervous but now I will re- tune the PIDs!
THNAKS!!
when I saw this setting I knew I v see it before- it even says "twitching" in the comment... I only did not see the relation because I never had problems with this before.
Anyways- it works now- thanks. Still is a little nervous but now I will re- tune the PIDs!
THNAKS!!
- Wed Mar 13, 2013 5:29 pm
- Forum: Software development
- Topic: 2.2 twitches while flying
- Replies: 20
- Views: 7815
2.2 twitches while flying
Dear all- I just installed 2.2. (Setup: Crius AIO Pro, Simon K ESCs, Y6 cinfiguration, 8" props, Oled, CRIUS V2 GPS). It flies nicely, GPS PH is awesome- BUT I have all 0.8 to 2 sec small "twitches" i.e. one (or may be 2 motors on one arm?) speed up for a very short time such a way th...
- Thu Mar 07, 2013 9:42 pm
- Forum: Software development
- Topic: Release 2.2 is coming
- Replies: 167
- Views: 59438
Re: Release 2.2 is coming: MINCHECK change?
Hello- I had no time to test the new version- anyways- thank you for all the great work! From my point of view Stars 112 is perfectly correct with his #define MINCHECK 1100 command hint. Almost had a few crashes before I knew this, so it really might be a good idea to change this number to a lower v...
- Thu Mar 07, 2013 4:24 pm
- Forum: Software development
- Topic: Sum PPM in CH6 and 7 passthrough AIO Pro
- Replies: 3
- Views: 1857
Re: Sum PPM in CH6 and 7 passthrough AIO Pro
Dear Mis, dear all- I finally found the time to work on this again- and did not find what you were referring to- sorry. What I found in the output.ino is (and from my understanding might be related): /**************** Cam stabilize Sevos ******************/ #if defined(SERVO_TILT) #if defined(A0_A1_...
- Wed Feb 27, 2013 2:29 pm
- Forum: Software development
- Topic: Gimbal-Plate Mounted MWC Board - Possible ??
- Replies: 2
- Views: 1186
Re: Gimbal-Plate Mounted MWC Board - Possible ??
Hi-
This site probably has the info you need- in German though
I do not know about your language skills but you might give google translate a try?
Let us know how it works for you
Greets
This site probably has the info you need- in German though
I do not know about your language skills but you might give google translate a try?
Let us know how it works for you
Greets
- Tue Feb 19, 2013 11:59 pm
- Forum: Software development
- Topic: multiWii SE v2.1 Setup Help : )
- Replies: 9
- Views: 14426
Re: multiWii SE v2.1 Setup Help : )
May be it is due to using an iPad- but I can not see your config file?
For sure a Multiwii SE is not a AIO Pro- so it will probably not work when defined as such.
For sure a Multiwii SE is not a AIO Pro- so it will probably not work when defined as such.
- Tue Feb 19, 2013 6:51 pm
- Forum: Software development
- Topic: multiWii SE v2.1 Setup Help : )
- Replies: 9
- Views: 14426
Re: multiWii SE v2.1 Setup Help : )
Hi- Important fact missing: what receiver are you using and how is it connected? Do the channels in the GUI show the correct remote ranges and directions when you move your sticks? How did you power your board during the test? The motors are all connected properly (you r referring to 1-6...ports are...
- Sun Feb 17, 2013 1:45 am
- Forum: Software development
- Topic: UART Radio project
- Replies: 112
- Views: 51450
Re: UART Radio project
Sounds great!
FYI: The 433 3DR modules work good for me (telemetry, changing settings)
Greets
FYI: The 433 3DR modules work good for me (telemetry, changing settings)
Greets
- Fri Jan 11, 2013 9:34 pm
- Forum: Ideas
- Topic: Idea: active compass compensation
- Replies: 7
- Views: 2889
Re: Idea: active compass compensation
Sounds good- thank you for your feedback!
Now just one of the brilliant programmers needs to volunteer
Greets
Now just one of the brilliant programmers needs to volunteer
Greets
- Thu Jan 10, 2013 11:58 pm
- Forum: Ideas
- Topic: Idea: active compass compensation
- Replies: 7
- Views: 2889
Idea: active compass compensation
Hi- I think it is a common problem with aio boards that the compass is influenced by the (high) currents in the battery / ESC cables. This might become an issue when using GPS or "headfree mode". At least for RTH- why not: - RTH enabled? - stop yaw - switch off motors for a (very) short ti...
- Wed Jan 09, 2013 3:19 pm
- Forum: Software development
- Topic: Sum PPM in CH6 and 7 passthrough AIO Pro
- Replies: 3
- Views: 1857
Sum PPM in CH6 and 7 passthrough AIO Pro
Hi all, I have a receiver spitting out PPMsum to a multiwii AIO Pro board. (CH 1-4 standard, CH 5 flight mode selection so far) Due to having an external gimbal controller I would need channels 6 and 7 as a direct output (ch6 and ch7 decoded from the PPM sum ). Best would be the outputs 44 and 46 on...
- Sat Dec 22, 2012 11:55 am
- Forum: Software development
- Topic: Flight Mode multi Position switch
- Replies: 0
- Views: 800
Flight Mode multi Position switch
Hi- Is it possible to select more different flight modes with 1 channel? (Like with Megapirate?) From the hardware: piece of cake (and a real plus for the Frsky users with their 8 CH bug...): just use a multi position switch and some resistors on a analog channel. Sad to have all the great options a...
- Fri Dec 21, 2012 11:06 pm
- Forum: Shields, boards and sensors
- Topic: Crius AIO Pro with 3DRadio 433 Mhz Telemetry
- Replies: 2
- Views: 3177
Re: Crius AIO Pro with 3DRadio 433 Mhz Telemetry
Awesome- thank you so much! Works fine and is really nice to have!
- Fri Dec 21, 2012 2:29 pm
- Forum: Shields, boards and sensors
- Topic: Crius AIO Pro with 3DRadio 433 Mhz Telemetry
- Replies: 2
- Views: 3177
Crius AIO Pro with 3DRadio 433 Mhz Telemetry
Hello- how to connect this module to the Crius AIO Pro? I connected it to TX3/RX3 (works with Megapirate NG) and changed the serial speed in the config.h to #define SERIAL_COM_SPEED 57600 (3DRs are configured accordingly) I connected the copter to a LiPo, the 3DRobot ground module to USB and opened ...
- Wed Nov 07, 2012 6:36 pm
- Forum: ESCs, propellers , servos and radios
- Topic: Alternative ESC firmware (reflashing)
- Replies: 640
- Views: 370729
Re: Alternative ESC firmware (reflashing)
Does the WiiESC FW also have a bootloader or will it "kill" the bootloader I have in my ESC from the SimonK FW? Did somobody try to use: m instead f using the Turnigy USB linker with the kkMulticopter Flash Tool? Thanks Btw: MT 2814-10 770kV is giving problems with original SimonK FW- for ...
- Wed Sep 12, 2012 12:30 am
- Forum: Shields, boards and sensors
- Topic: SOLVED! NAVIGATRON V1 update to V2 Problem
- Replies: 2
- Views: 1533
Re: SOLVED! NAVIGATRON V1 update to V2 Problem
Thanks a lot!
Everything seems to work now.
I tried PH today (windy day) without further tuning on my HEX- keeps position within few meters! Still have to see if it keeps the settings and how RTH works
Awesome work from everybody involved
Greets
Everything seems to work now.
I tried PH today (windy day) without further tuning on my HEX- keeps position within few meters! Still have to see if it keeps the settings and how RTH works
Awesome work from everybody involved
Greets
- Fri Aug 31, 2012 10:04 am
- Forum: Shields, boards and sensors
- Topic: SOLVED! NAVIGATRON V1 update to V2 Problem
- Replies: 2
- Views: 1533
SOLVED! NAVIGATRON V1 update to V2 Problem
Hi- sorry- frustration level got too high, too much time wasted already. I wanted to update the NAVIGATRON V1 to V2 (firmware only, run it with 3,3V) - I just connect a FTDI cable (also gives me Ub 3,3V) to the Navigatron (what is the pinout in the N.board? Shematics are incorrect it looks to me, th...
- Wed May 23, 2012 12:05 pm
- Forum: Software development
- Topic: GPS integration
- Replies: 1724
- Views: 896755
Re: GPS integration
Hi-
Just to get this straight- when I use the newest I2C version of the SW for the multiwii and connect a Navigatron GPS board with the old FW it will be initialized for 10Hz anyways- so no need for FW change on the Navigatron board?
Thank you for all the hard work and especially to you, EOSbandi!!!
Just to get this straight- when I use the newest I2C version of the SW for the multiwii and connect a Navigatron GPS board with the old FW it will be initialized for 10Hz anyways- so no need for FW change on the Navigatron board?
Thank you for all the hard work and especially to you, EOSbandi!!!
- Sun May 06, 2012 9:14 pm
- Forum: General discussions
- Topic: anyone going to landkamp 2012?
- Replies: 3
- Views: 1478
Re: anyone going to landkamp 2012?
I also will be there to represent the noob fraction .
@hamburger: I actually live next door to Hamburg!
@hamburger: I actually live next door to Hamburg!
- Sun May 06, 2012 5:22 am
- Forum: Software development
- Topic: GPS integration
- Replies: 1724
- Views: 896755
Re: GPS integration
@EOSBandi
Thank you so much for the quick reply!
I ll stay tuned because it is bejond my horizon to implement it myself (or at leat I do not have the time )
Kind regards
Roman
Thank you so much for the quick reply!
I ll stay tuned because it is bejond my horizon to implement it myself (or at leat I do not have the time )
Kind regards
Roman
- Sat May 05, 2012 3:42 pm
- Forum: Software development
- Topic: GPS integration
- Replies: 1724
- Views: 896755
Re: GPS integration
Hello- Does anybody know how to change the GPS refresh rate of a NAVIGATRON I2C GPS module? I really would love to test the serial GPS Dev Version of EOSbandi but also see no point in trying this with a refresh rate of 1Hz. The module should be able to output a 10 Hz position signal. Thanks and have...
- Thu May 03, 2012 9:51 pm
- Forum: Software development
- Topic: CRIUS LCD BUG WITH 2.0
- Replies: 53
- Views: 25116
Re: CRIUS LCD BUG WITH 2.0
I also really like it!
Thank you so much for the effort- much better then before, also with 1.9.
Thank you so much for the effort- much better then before, also with 1.9.
- Wed Apr 25, 2012 11:29 pm
- Forum: Software development
- Topic: CRIUS LCD BUG WITH 2.0
- Replies: 53
- Views: 25116
Re: CRIUS LCD BUG WITH 2.0
Hi-
Before I reflash my crius LCD- is the new FW downwards compatible to multiwii 1.9 ?
Thanks a lot for all the great work!
(FYI: I am new here- and love Crius SE boards! Working on FPV Hexa with I2C GPS- probably with new 2.0 dev ver... Tons of questions to come .
Before I reflash my crius LCD- is the new FW downwards compatible to multiwii 1.9 ?
Thanks a lot for all the great work!
(FYI: I am new here- and love Crius SE boards! Working on FPV Hexa with I2C GPS- probably with new 2.0 dev ver... Tons of questions to come .