MultiWii

Finally found the culprit, it was my LC filter, it made the input voltage drop below 4.5V which is definitively too low for MAX Chip on the OSD.
Now there is nothing left, which could hinder the mayden in the next days.

When osd is connected to the fc, it is able to ready the RC commands from the tx. If the RC channel used for switching OSD layouts is set to a blank one, it maybe that this then selects a different screenlayout which is set to show no data. Set all the HUD - xx values to 0 on top RHS of display and...

Did You check if right Props in Motors, You might have switched by mistake.

When osd is connected to the fc, it is able to ready the RC commands from the tx. If the RC channel used for switching OSD layouts is set to a blank one, it maybe that this then selects a different screenlayout which is set to show no data. Set all the HUD - xx values to 0 on top RHS of displ'ay an...

@ Leo - brill - thanks Also there may be an issue with saving rc and pid on .8 I hope fixed on the latest. i am waiting to get to my garage to test on a copter. @ duke Assuming this isnt a wiring issue, most likely is you have a blank screen layout selected. I can't think of any other cause. I've b...

Hi, I got the following issue, I get no signal on Video Out of my MinimOSD. Got the following configuration: Flip32+ with Cleanflight 1.9 Ublox GPS connected to FC. MinimOSD with MW OSD 1.4.1 Fatschark 600 TVL configured for PAL. As long as RX and TX on the OSD is not connected to the FC I have a si...

Hi, I got the following issue, I get no signal on Video Out of my MinimOSD. Got the following configuration: Flip32+ with Cleanflight 1.9 Ublox GPS connected to FC. MinimOSD with MW OSD 1.4.1 Fatschark 600 TVL configured for PAL. As long as RX and TX on the OSD is not connected to the FC I have a si...

Hi haydent, late tonight I checked and changed the code section according to your post of Fri Dec 06, 2013 9:49 am. And the debug is always showing 1023 when the battery is at least 7.0V It is showing around 796 for a 1S battery with 3,8V. So it seems something is wrong and sending always 5V to the ...

Yes, you are right in multiwii.ino, but the code there lookslike the one you wrote for 2.3.

Btw, uint8 is 1-255 os is vbatscale defined as int8 which is a signed integer ranging from -128 to 127?

Hi haydent,

Where is the mentioned code located? Could Not find it

Means i will have to move from 2.2 to 2.3, as the Code you mean is clearly 2.3

Hi haydent, sounds logical, but I tested with a 1S Lipo as well, and there the displayed Battery Voltage in the GUI is quite different about 2V below the voltage displayed with a 2S Lipo, so something is getting through and is fed to the right pin. Further no Lipo and the GUI shows a battery voltage...

Hi, I have already tried a lot today to try to get the battery voltage displayed correctly in the GUI. I am using a NanoWii with MultiWii 2.2. I have tested several values for VBATSCALE ranging from 200 up to 5000, but without real success. I use a 2S setup. with full Lipo (8.1V) and an rather empty...

Somehow it does not work for me, I have 1002 at lowest throttle stick and even then arming the motors using AUX2 does not work. On my MX-16 I have set a switch for arming the motors, the switch has two states 1000-2000, is assigned to a channel which is linked to AUX2. I leave the throttel stick at ...

Hi, I want to arm my motors using a switch on my RC, this should worl as far as I know using one of the AUX channels. I have setup on my RC, that the switch is linked to AUX2, in the GUI, I have check the box for ARM on AUX2 High, but the motors are not arming when I activate the switch. I see in th...

Hi, I have the following IMU: 10DOF IMU GY-86 MPU6050+HMC5883l+MS5611 With the following specs, which IMU should I activate in the config.h file? It seems to be very similar to the FreeIMU 0.43 from Fabio Varessano, but I am not sure if it is the right one to uncomment. Could someone please give me ...