Search found 33 matches

by p25o1
Fri Mar 22, 2013 6:13 pm
Forum: MultiWii tweaking - flying experience
Topic: Multiwii 2.2 - GPS hold
Replies: 93
Views: 124573

Re: Multiwii 2.2 - GPS hold

Have you checked the MAG? 1 - Is it calibrated 2 - Does the MAG arrow points in the same direction at any throttle applied? (Armed With Props on, hold it down by hand) 3 - check the "2" for E, W, S, N. thanks for the help,, i did the mag calibration, but as you suggested i started the mot...
by p25o1
Fri Mar 22, 2013 6:18 am
Forum: MultiWii tweaking - flying experience
Topic: Multiwii 2.2 - GPS hold
Replies: 93
Views: 124573

Re: Multiwii 2.2 - GPS hold

same issue here even after disabling GPS_LEAD_FILTER

i'm using quadrino board ms
i2c gps (flytron v2) 8 satellites were locked
800kva 10"props , 30amp esc

i started to increased the PosR D 0.2 at a time but didn't help
increased PosR P 0.2 at a time but didn't also.

any suggestions / thanks
by p25o1
Mon Nov 26, 2012 3:45 am
Forum: Software development
Topic: GPS integration
Replies: 1724
Views: 880704

Re: GPS integration

hi everyone , just want to confirm if gps hold is working in r1240, since i'm not able to make it work in angle or horizon mode.
by p25o1
Sat Nov 24, 2012 10:06 pm
Forum: Software development
Topic: Angle vs Horizon
Replies: 23
Views: 17820

Re: Angle vs Horizon

i'm using build r1240 to test out horizon mode, and its very smooth.

is gps pos hold disabled on horizon mode at this build ? didn't work for me.

altitude hold was nice and stable, but needed some PID tuning on my build.
by p25o1
Tue Oct 16, 2012 3:28 am
Forum: General discussions
Topic: Does ACC get disabled under high stick movements?
Replies: 56
Views: 41596

Re: Does ACC get disabled under high stick movements?

i used acrotraining mode some time back , and i really enjoyed the flips,

can we now assign it to aux channel in the gui ?

if not will it behave in this way

if i activate it , will it only work in angle mode, and will it be disabled if i switch to horizon mode ?

thx
by p25o1
Mon Sep 03, 2012 4:54 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1380995

Re: Naze32 hardware discussion thread

not sure if you saw this

http://www.goodluckbuy.com/miniature-fo ... 883l-.html

its a mini stm32 quad. should i order one :-) and will we see it run multiwii 32 soon.
by p25o1
Mon Sep 03, 2012 3:33 pm
Forum: Boards
Topic: Naze32 hardware discussion thread
Replies: 3249
Views: 1380995

Re: Naze32 hardware discussion thread

+1 for the naze32,,, i like the size/sensors used, and the effort put to port multiwii to 32bit platforms. just few question, and i hope i'm not opening a can of worms is dongs/timecop the only developer working on the 32bit port of multiwii? what is the overall direction from multiwii community to ...
by p25o1
Sat Aug 18, 2012 3:11 pm
Forum: Software development
Topic: GPS integration
Replies: 1724
Views: 880704

Re: GPS integration

managed to test the gps PosHold and RTH. my set up was using: quadrino rev 1e mwc flytron i2c gps. multiwii 2.1 was used, and for my setup i can say it was "out of the box" experience!!! i was prepared for a long tuning session , but i was amazed that every thing just worked. hats off to t...
by p25o1
Thu Aug 16, 2012 12:06 pm
Forum: Software development
Topic: _shared r1058 EXT_MOTOR_RANGE issue
Replies: 8
Views: 2702

Re: _shared r1058 EXT_MOTOR_RANGE issue

can i enable the EXT_MOTOR_RANGE on a pro mini on a normal esc ? i thought , since a normal esc can handle a resolution of 1000 steps when used with a promicro / mega can a promini push 240 steps resolution using EXT_MOTOR_RANGE to a normal ESC. for testing purpose i did that , and there is a strang...
by p25o1
Wed Jul 25, 2012 3:44 pm
Forum: Software development
Topic: GPS integration
Replies: 1724
Views: 880704

Re: GPS integration

brettwal wrote:I have the GPS below working via i2c.

http://www.ebay.com/itm/130723245783?ss ... 1497.l2649


i just visited the site, i don't see the i2c pins on the board,,

can you elaborate on how you got it to work on i2c plz

i'm looking for a working i2c gps module , since my wmc has only 1 i2c port free , and i'm using the serial for gui :?
by p25o1
Mon Jul 16, 2012 2:07 pm
Forum: MultiWii tweaking - flying experience
Topic: Pseudo-derivative controller for level mode
Replies: 3
Views: 3242

Re: Pseudo-derivative controller for level mode

same here ,

i was going though 2.1 notes and Pseudo-derivative link is removed from the forums

:?:
by p25o1
Sun Jul 15, 2012 9:20 pm
Forum: Software development
Topic: mobiDrone nano arduino OSD for MultiWii with PID config
Replies: 295
Views: 126284

Re: mobiDrone nano arduino OSD for MultiWii with PID config

i really like the way this osd is thought of,

such a small foot print!!!

can i ask for some clarification,

if i'm using the i2c link for a gps sensor,, can i use the same port for the osd ?
if not ,
is there an alternative way to get the osd data from the mwc ?

thx
by p25o1
Sun Jul 15, 2012 9:11 pm
Forum: Software development
Topic: MultiWii release 2.1 is here :)
Replies: 52
Views: 46623

Re: MultiWii release 2.1 is here :)

congratulation,

looking forward to try it out asap :D

gps is pending for me since i'm waiting for an i2c board ;)
by p25o1
Tue Jul 10, 2012 5:43 pm
Forum: Software development
Topic: PID settings for EXT_MOTOR_RANGE
Replies: 19
Views: 6119

Re: PID settings for EXT_MOTOR_RANGE

oh , cool ,

i'll give it a try anyways to see how the esc respond with it :-)
by p25o1
Tue Jul 10, 2012 2:04 pm
Forum: Software development
Topic: PID settings for EXT_MOTOR_RANGE
Replies: 19
Views: 6119

Re: PID settings for EXT_MOTOR_RANGE

simonk flashed ESC work fine with my setup

but as you pointed out it will not work with EXT_MOTOR_RANGE ,
when I enable it with the same simonk flashed ESC , it only spins the motor when i give it full throttle.

no issues, i'll leave this option for now,
by p25o1
Tue Jul 10, 2012 1:04 pm
Forum: Software development
Topic: PID settings for EXT_MOTOR_RANGE
Replies: 19
Views: 6119

Re: PID settings for EXT_MOTOR_RANGE

i have simon Flashed esc,,, will they do the job/work? i enabled the option it but the motors didn’t work initially. after applying full throttle they started to spin, i'm asking since i see in the code with EXT_MOTOR_RANGE "promicro - no support for EXT_MOTOR_RANGE atm." i just wanted to ...
by p25o1
Tue Jul 10, 2012 9:51 am
Forum: Software development
Topic: PID settings for EXT_MOTOR_RANGE
Replies: 19
Views: 6119

Re: PID settings for EXT_MOTOR_RANGE

hi everyone, i just have a question about the EXT_MOTOR_RANGE option, i posted the same question here http://www.multiwii.com/forum/viewtopic.php?f=8&t=2024 i missed this post. i'm using a quadrino zoom rev 1e which is based on the Nano ATmega328 can it support the EXT_MOTOR_RANGE option, and if...
by p25o1
Mon Jul 09, 2012 11:20 pm
Forum: Software development
Topic: question about EXT MOTOR RANGE
Replies: 6
Views: 2248

Re: question about EXT MOTOR RANGE

i have flashed my esc with simon firmware ,

i wanted to know that will the EXT_MOTOR_RANGE give me their full potential?

will the esc still act as a normal esc if i don't enable EXT_MOTOR_RANGE.
by p25o1
Mon Jul 09, 2012 9:32 pm
Forum: Software development
Topic: question about EXT MOTOR RANGE
Replies: 6
Views: 2248

question about EXT MOTOR RANGE

hi everyone,

i just have a question about the EXT_MOTOR_RANGE option,

i'm using a quadrino zoom rev 1e which is based on the Nano ATmega328

can it support the EXT_MOTOR_RANGE option, and if no why?

if i enable this option , do i need to re calibrate my escs?

thx everyone
by p25o1
Sun Jul 08, 2012 1:32 pm
Forum: Software development
Topic: playing with acc-z altitude hold
Replies: 44
Views: 18497

Re: playing with acc-z altitude hold

just to understand this better,

1-both the baro and acc-z will be used to keep the altitude hold?

2-can this be pushed to have a semi-position hold? i like to dream loud lool
by p25o1
Thu Jul 05, 2012 9:28 am
Forum: Ideas
Topic: Inflight ACC-calibration
Replies: 127
Views: 72421

Re: Inflight ACC-calibration

thx ,, i'll try it out.

edit:
just figured out the "branch" part lool,

i'll try it out ,

next stop, ACROTRAINER branch, nice to try out
by p25o1
Thu Jul 05, 2012 8:01 am
Forum: Ideas
Topic: Inflight ACC-calibration
Replies: 127
Views: 72421

Re: Inflight ACC-calibration

thx for the response,

is it fixed in the post r949 builds , /or can you share with me a the code to fix it.

not sure what is "shared trunk" lool

thx
by p25o1
Thu Jul 05, 2012 6:29 am
Forum: Software development
Topic: GPS integration
Replies: 1724
Views: 880704

Re: GPS integration

found this module,

http://www.drotek.fr/shop/en/88-i2c-pa6c-gps-llc.html

but i really like the size of the navigator from flytron!

i guess i have to wait for stock :-(
by p25o1
Thu Jul 05, 2012 6:20 am
Forum: Ideas
Topic: Inflight ACC-calibration
Replies: 127
Views: 72421

Re: Inflight ACC-calibration

hi all, the inflight calibration is a very cool idea, and very practical to use. for me i end up changing the camera location on the quad frequently, so i always have to go in loops (take off->observe->land->tune->takeoff->loop) to calibrate. i tried to enable the in flight calibration, but i get &q...
by p25o1
Wed Jul 04, 2012 6:59 am
Forum: Software development
Topic: GPS integration
Replies: 1724
Views: 880704

Re: GPS integration

hi all,

i'm waiting for the navigator board from flytron, but its still in back order :-(

serial is not a good idea for my quadrino, since i'll have to share the usb port.

is there another i2c gps board that i can buy? please share.
by p25o1
Wed Jun 27, 2012 3:48 am
Forum: Software development
Topic: Quadrino Zoom Dev Baro - Config / fix
Replies: 0
Views: 970

Quadrino Zoom Dev Baro - Config / fix

Hi everyone, just wanted to share this. i had problems in the baro / I2c errors after updating my quadrino zoom rev 1e to the latest 2.1 devs. after some tracing , it was a simple issue with the ms5611 i2c baro address. i guess you can change it in either of these files: in def.h #if defined(QUADRIN...
by p25o1
Tue Jun 26, 2012 11:16 am
Forum: Software development
Topic: Details on MultiWii_dev_20120622
Replies: 5
Views: 2147

Re: Details on MultiWii_dev_20120622

sweet, i was looking for this too, and didn't know how to link the date release with R release lool .
by p25o1
Tue Jun 26, 2012 11:11 am
Forum: Software development
Topic: mobiDrone nano arduino OSD for MultiWii with PID config
Replies: 295
Views: 126284

Re: mobiDrone nano arduino OSD for MultiWii with PID config

i'm also intrested in the i2c model, since my mwc share serial and usb :-(
by p25o1
Thu Jun 21, 2012 6:27 am
Forum: Software development
Topic: GPS integration
Replies: 1724
Views: 880704

Re: GPS integration

Hi everyone, Congratulation on the GPS progress, looks very solid , warthox video/demo put a smile on my face. Some advice before i place the order plz i have a quadrino rev 1e board , and in the posts, members used a i2c gps board with it successfully. do you advise me to go for a serial gps board?...
by p25o1
Wed Jun 20, 2012 1:19 pm
Forum: MultiWii tweaking - flying experience
Topic: PID tuning, YAW
Replies: 4
Views: 4086

Re: PID tuning, YAW

i'm having the same issue ,

i kept increasing the P for the yaw to solve it , but not sure if this is the best approach, since i started losing altitude when pitching or rolling :-(

any advice on this issue.
by p25o1
Fri Apr 27, 2012 1:37 pm
Forum: Ideas
Topic: Position Hold with Optical Flow sensor - done
Replies: 214
Views: 131583

Re: Position Hold with Optical Flow sensor - done

i'm using a quadrino rev 1e board
http://flyingeinstein.com/index.php/tutorials/knowit

can i do the following

#define OPTFLOW 3080
define OF_SCLK A0
define OF_MISO A1
define OF_MOSI D8
define OF_NCS A6

A0, A1, D8 are available on the ezconnect cable
A6 is available on the board.
by p25o1
Fri Apr 27, 2012 11:32 am
Forum: Ideas
Topic: Position Hold with Optical Flow sensor - done
Replies: 214
Views: 131583

Re: Position Hold with Optical Flow sensor - done

hi alexmos,

i managed to get the ADNS-3080 optical sensor from diydrones.

can you advice on the connection diagram plz.

looking forward to get it up and running and test with you guys

thanks
by p25o1
Mon Apr 16, 2012 12:03 am
Forum: Ideas
Topic: Throttle expo
Replies: 22
Views: 10602

Re: Throttle expo

Hi @alexmos. Would you share your code for throttle stick altitude control when Baro is enabled? I will merge it (if possible) with V2pre4 and post my experience. Cheers H. Yes, but there are few errors in my code. I will finish them soon and share revision r16 after some testing. After that, I wil...