MultiWii

Have you checked the MAG? 1 - Is it calibrated 2 - Does the MAG arrow points in the same direction at any throttle applied? (Armed With Props on, hold it down by hand) 3 - check the "2" for E, W, S, N. thanks for the help,, i did the mag calibration, but as you suggested i started the mot...

same issue here even after disabling GPS_LEAD_FILTER

i'm using quadrino board ms
i2c gps (flytron v2) 8 satellites were locked
800kva 10"props , 30amp esc

i started to increased the PosR D 0.2 at a time but didn't help
increased PosR P 0.2 at a time but didn't also.

any suggestions / thanks

hi everyone , just want to confirm if gps hold is working in r1240, since i'm not able to make it work in angle or horizon mode.

i'm using build r1240 to test out horizon mode, and its very smooth.

is gps pos hold disabled on horizon mode at this build ? didn't work for me.

altitude hold was nice and stable, but needed some PID tuning on my build.

i used acrotraining mode some time back , and i really enjoyed the flips,

can we now assign it to aux channel in the gui ?

if not will it behave in this way

if i activate it , will it only work in angle mode, and will it be disabled if i switch to horizon mode ?

thx

not sure if you saw this

http://www.goodluckbuy.com/miniature-fo ... 883l-.html

its a mini stm32 quad. should i order one and will we see it run multiwii 32 soon.

+1 for the naze32,,, i like the size/sensors used, and the effort put to port multiwii to 32bit platforms. just few question, and i hope i'm not opening a can of worms is dongs/timecop the only developer working on the 32bit port of multiwii? what is the overall direction from multiwii community to ...

managed to test the gps PosHold and RTH. my set up was using: quadrino rev 1e mwc flytron i2c gps. multiwii 2.1 was used, and for my setup i can say it was "out of the box" experience!!! i was prepared for a long tuning session , but i was amazed that every thing just worked. hats off to t...

can i enable the EXT_MOTOR_RANGE on a pro mini on a normal esc ? i thought , since a normal esc can handle a resolution of 1000 steps when used with a promicro / mega can a promini push 240 steps resolution using EXT_MOTOR_RANGE to a normal ESC. for testing purpose i did that , and there is a strang...

brettwal wrote:I have the GPS below working via i2c.

http://www.ebay.com/itm/130723245783?ss ... 1497.l2649

i just visited the site, i don't see the i2c pins on the board,,

can you elaborate on how you got it to work on i2c plz

i'm looking for a working i2c gps module , since my wmc has only 1 i2c port free , and i'm using the serial for gui

same here ,

i was going though 2.1 notes and Pseudo-derivative link is removed from the forums

i really like the way this osd is thought of,

such a small foot print!!!

can i ask for some clarification,

if i'm using the i2c link for a gps sensor,, can i use the same port for the osd ?
if not ,
is there an alternative way to get the osd data from the mwc ?

thx

congratulation,

looking forward to try it out asap

gps is pending for me since i'm waiting for an i2c board

oh , cool ,

i'll give it a try anyways to see how the esc respond with it

simonk flashed ESC work fine with my setup

but as you pointed out it will not work with EXT_MOTOR_RANGE ,
when I enable it with the same simonk flashed ESC , it only spins the motor when i give it full throttle.

no issues, i'll leave this option for now,

i have simon Flashed esc,,, will they do the job/work? i enabled the option it but the motors didn’t work initially. after applying full throttle they started to spin, i'm asking since i see in the code with EXT_MOTOR_RANGE "promicro - no support for EXT_MOTOR_RANGE atm." i just wanted to ...

hi everyone, i just have a question about the EXT_MOTOR_RANGE option, i posted the same question here http://www.multiwii.com/forum/viewtopic.php?f=8&t=2024 i missed this post. i'm using a quadrino zoom rev 1e which is based on the Nano ATmega328 can it support the EXT_MOTOR_RANGE option, and if...

i have flashed my esc with simon firmware ,

i wanted to know that will the EXT_MOTOR_RANGE give me their full potential?

will the esc still act as a normal esc if i don't enable EXT_MOTOR_RANGE.

hi everyone,

i just have a question about the EXT_MOTOR_RANGE option,

i'm using a quadrino zoom rev 1e which is based on the Nano ATmega328

can it support the EXT_MOTOR_RANGE option, and if no why?

if i enable this option , do i need to re calibrate my escs?

thx everyone

just to understand this better,

1-both the baro and acc-z will be used to keep the altitude hold?

2-can this be pushed to have a semi-position hold? i like to dream loud lool

thx ,, i'll try it out.

edit:
just figured out the "branch" part lool,

i'll try it out ,

next stop, ACROTRAINER branch, nice to try out

thx for the response,

is it fixed in the post r949 builds , /or can you share with me a the code to fix it.

not sure what is "shared trunk" lool

thx

found this module,

http://www.drotek.fr/shop/en/88-i2c-pa6c-gps-llc.html

but i really like the size of the navigator from flytron!

i guess i have to wait for stock

hi all, the inflight calibration is a very cool idea, and very practical to use. for me i end up changing the camera location on the quad frequently, so i always have to go in loops (take off->observe->land->tune->takeoff->loop) to calibrate. i tried to enable the in flight calibration, but i get &q...

hi all,

i'm waiting for the navigator board from flytron, but its still in back order

serial is not a good idea for my quadrino, since i'll have to share the usb port.

is there another i2c gps board that i can buy? please share.

Hi everyone, just wanted to share this. i had problems in the baro / I2c errors after updating my quadrino zoom rev 1e to the latest 2.1 devs. after some tracing , it was a simple issue with the ms5611 i2c baro address. i guess you can change it in either of these files: in def.h #if defined(QUADRIN...

sweet, i was looking for this too, and didn't know how to link the date release with R release lool .

i'm also intrested in the i2c model, since my mwc share serial and usb

Hi everyone, Congratulation on the GPS progress, looks very solid , warthox video/demo put a smile on my face. Some advice before i place the order plz i have a quadrino rev 1e board , and in the posts, members used a i2c gps board with it successfully. do you advise me to go for a serial gps board?...

i'm having the same issue ,

i kept increasing the P for the yaw to solve it , but not sure if this is the best approach, since i started losing altitude when pitching or rolling

any advice on this issue.

i'm using a quadrino rev 1e board
http://flyingeinstein.com/index.php/tutorials/knowit

can i do the following

#define OPTFLOW 3080
define OF_SCLK A0
define OF_MISO A1
define OF_MOSI D8
define OF_NCS A6

A0, A1, D8 are available on the ezconnect cable
A6 is available on the board.

hi alexmos,

i managed to get the ADNS-3080 optical sensor from diydrones.

can you advice on the connection diagram plz.

looking forward to get it up and running and test with you guys

thanks

Hi @alexmos. Would you share your code for throttle stick altitude control when Baro is enabled? I will merge it (if possible) with V2pre4 and post my experience. Cheers H. Yes, but there are few errors in my code. I will finish them soon and share revision r16 after some testing. After that, I wil...