Search found 23 matches
- Wed Jun 05, 2013 5:27 am
- Forum: Ideas
- Topic: wishlist for v2.3
- Replies: 104
- Views: 43336
Re: wishlist for v2.3
It help for novices.
- Fri May 31, 2013 11:58 am
- Forum: General discussions
- Topic: Passthru for ESC Programming.
- Replies: 5
- Views: 1600
Re: Passthru for ESC Programming.
Do not forget to remove props before use CALIB_ESC, it will make full throttle few seconds.
- Thu Apr 04, 2013 5:57 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: Motors not arming on my multiwii.
- Replies: 6
- Views: 5149
Re: Motors not arming on my multiwii.
make on all sticks chanell (throttle, elevator, ailerons, rudder) endpoints 125%
- Thu Apr 04, 2013 11:48 am
- Forum: Shields, boards and sensors
- Topic: About to give up!!!
- Replies: 13
- Views: 4229
Re: About to give up!!!
Screw mainboard with hard bolts, preferably plastic or alu.
It is bad idea to make all those antivibration pads, especialy if above the board hanging mass of wires or other boards.
Mainboard have not to be in movement during flight.
It is bad idea to make all those antivibration pads, especialy if above the board hanging mass of wires or other boards.
Mainboard have not to be in movement during flight.
- Tue Apr 02, 2013 9:17 pm
- Forum: Shields, boards and sensors
- Topic: Crius I2C Nav and Ublox Neo6m Dilemma
- Replies: 19
- Views: 29381
Re: Crius I2C Nav and Ublox Neo6m Dilemma
baud rate have to be 57600, but before please show your setup?
Mainboard and how you connect gps.
Mainboard and how you connect gps.
- Tue Apr 02, 2013 6:03 pm
- Forum: Shields, boards and sensors
- Topic: Crius I2C Nav and Ublox Neo6m Dilemma
- Replies: 19
- Views: 29381
Re: Crius I2C Nav and Ublox Neo6m Dilemma
Navboard?? Something new ...
Which flight controller do you use?
Could you post your config.ino (part of gps definitions) and pictures of your setup?
Which flight controller do you use?
Could you post your config.ino (part of gps definitions) and pictures of your setup?
- Tue Apr 02, 2013 4:12 pm
- Forum: Shields, boards and sensors
- Topic: Crius I2C Nav and Ublox Neo6m Dilemma
- Replies: 19
- Views: 29381
Re: Crius I2C Nav and Ublox Neo6m Dilemma
Your config? Connection? GPS ?
- Mon Apr 01, 2013 9:42 am
- Forum: Getting Started - MultiWii config and setup
- Topic: Hobby King Multiwii Mini Flight Controller w/FTDI Interface
- Replies: 10
- Views: 5162
Re: Hobby King Multiwii Mini Flight Controller w/FTDI Interf
Pitch and roll stickis seems heve not enough range.
Seems you need to make range on your rc for sticks 125% on every side.
Check center of range for all sticks is 1500, tune with subtrim or chanel ajustment on your rc, and range have to be 1000-2000.
Seems you need to make range on your rc for sticks 125% on every side.
Check center of range for all sticks is 1500, tune with subtrim or chanel ajustment on your rc, and range have to be 1000-2000.
- Thu Mar 28, 2013 5:21 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1380396
Re: Naze32 hardware discussion thread
Problem of slow stick response resolved with increasing D up to 100 in Level section.
- Tue Mar 26, 2013 5:43 pm
- Forum: Boards
- Topic: Naze32 hardware discussion thread
- Replies: 3249
- Views: 1380396
Re: Naze32 hardware discussion thread
How to increase speed of reaction on stick input? On naze32 there is so slow reaction comparing with other board. It has good reaction on rudder but not on aileron/elevator. If to keep stick in position long enough copter can reach disired position but with lag. I made few attempt to tune PID but it...
- Mon Mar 25, 2013 10:17 am
- Forum: MultiWii tweaking - flying experience
- Topic: Multiwii 2.2 - GPS hold
- Replies: 93
- Views: 124571
Re: Multiwii 2.2 - GPS hold
Nice work Scrat!
I have the same configuration but result still far from perfect. I installed it on quadro and octo .. sometimes it can hold 3x3m, but mostly drift +-20-30m.
Could you please post settings? Batt 3s or 4s? other PIDs? Conf section of GPS ? Motors and ESC ?
Pictures?
I have the same configuration but result still far from perfect. I installed it on quadro and octo .. sometimes it can hold 3x3m, but mostly drift +-20-30m.
Could you please post settings? Batt 3s or 4s? other PIDs? Conf section of GPS ? Motors and ESC ?
Pictures?
- Sun Mar 24, 2013 2:23 pm
- Forum: ESCs, propellers , servos and radios
- Topic: HK Simonk ESC (solved)
- Replies: 8
- Views: 4013
Re: HK Simonk ESC
Which esc you got from HK ? link? I am doubt that they are selling simonk loaded. Parhaps it is possible to load simonk fw.
- Fri Mar 22, 2013 11:00 pm
- Forum: ESCs, propellers , servos and radios
- Topic: HK Simonk ESC (solved)
- Replies: 8
- Views: 4013
Re: HK Simonk ESC
Minthrottle depends on motors not on esc, just increase value till reliable start and rotation of motors.
- Tue Mar 12, 2013 6:11 pm
- Forum: Ideas
- Topic: HOTT Telemetry integration
- Replies: 63
- Views: 35986
Re: HOTT Telemetry integration
I can make some tests.
I have mini for interface, and quads with Crius AIO + gps with free aux ports.
Do I need something else?
I have mini for interface, and quads with Crius AIO + gps with free aux ports.
Do I need something else?
- Tue Mar 12, 2013 6:03 pm
- Forum: Ideas
- Topic: wishlist for v2.3
- Replies: 104
- Views: 43336
Re: wishlist for v2.3
ebourlet wrote:Failsafe descent rate based on barometric pressure sensor based rate of descent rather than preset min throttle + set value.
+1
- Mon Mar 04, 2013 6:55 pm
- Forum: Software development
- Topic: Release 2.2 is coming
- Replies: 167
- Views: 56473
Re: Release 2.2 is coming
On horizon and on acro modes for faster small loop we have to drop throttle but if we drop throttle to zero the copter just drop in upside down position without steering possibility. This absence of steering also is a source of unstable descend at zero throttle, but people often use fast descend met...
- Tue Feb 26, 2013 2:29 pm
- Forum: Software development
- Topic: Release 2.2 is coming
- Replies: 167
- Views: 56473
Re: Release 2.2 is coming
What is a source of constant drift if the bare board are placed on a table with disconnected motors? Arm the "motors", add throttle and we can observe slow constant decreasing of output magnitude on Rear L motor in time. In one two minutes it diverse with another motors ~100 sometimes. - m...
- Wed Feb 20, 2013 7:11 pm
- Forum: ESCs, propellers , servos and radios
- Topic: Alternative ESC firmware (reflashing)
- Replies: 640
- Views: 337674
Re: Alternative ESC firmware (reflashing)
Alll, effectively drain current (energy) back to the battery ... means loss of 95% instead of 100%.
- Sat Feb 16, 2013 8:09 pm
- Forum: Software development
- Topic: MultiWii dev1342 issues
- Replies: 21
- Views: 6417
Re: MultiWii dev1342 issues
Not how to get print, but how to go there ?
what shall I to do to see tabs DefaultMW Servo Config ?
what shall I to do to see tabs DefaultMW Servo Config ?
- Sat Feb 16, 2013 7:46 pm
- Forum: Software development
- Topic: MultiWii dev1342 issues
- Replies: 21
- Views: 6417
Re: MultiWii dev1342 issues
There's a #ifdef LOG_PERMANENT missing in that dev R1342 . In my test dev it works. http://multiwii.googlecode.com/svn/branches/PatrikE/Servotest.zip Doe's this look intresting? Still some space left in the Config TAB!... MWii.jpg MWiiG.jpg How do you get this type of screens in MW conf ??
- Wed Feb 06, 2013 1:34 am
- Forum: Ideas
- Topic: wishlist for v2.2 - CLOSED
- Replies: 150
- Views: 46135
Re: wishlist for v2.2
Telemetry for Graupner Hott system.
- Sun Mar 18, 2012 11:58 am
- Forum: Software development
- Topic: Drift (resolved)
- Replies: 1
- Views: 1153
Re: Drift (resolved)
The centre position of rc sticks not was exactly corresponded with value 1500 I am using Jeti modules and sattelite receivers with ppm connection, seems there is some difference between RC centre position and perception of centre value 1500 in mw soft. Simple subtrimming on rc or jeti box resolve th...
- Wed Mar 14, 2012 9:53 pm
- Forum: Software development
- Topic: Drift (resolved)
- Replies: 1
- Views: 1153
Drift (resolved)
Tested with 3 copters with 3 different boards, motors and frames, Rxs and Txrc Ver. 2.01 and now with 2.02 All in QuadX configuration: 1 Flydyino mega + ATAVRSBIN1 2 MiniWii bare 3 MiniPro + Citrus2.1 In all cases drift to forward and right. In all cases motor#4 (rear left) had far higher temperatur...