MultiWii

Hi

Could anyboby post his PID Settings from POS, POSR and NAVR ?
I don´t get reliable settings that the copter stills more or less quiet in the air....
What version from Eosbandi do you use ? (Currently I have installed the R33)

greetz
Karsten

Hi

I´ve cleared the eprom and flashed the firmware again..
but there is still the one I2C Error.. but only one !?!?

Hi I won´t open a new thread, so I write in this one. I have a strange problem with the update I´ve done from MW 2.0 to MW 2.1 The horizont of the roll and pitch aren´t in level after pushing the Calib ACC button. There´s also exactly ONE I2C-Error... but the copter flies. What could be the reason f...

Hi

Where can I find the code for the I2C Sonar ?

Karsten

Hi

I saw that there´s a new DEV Version at the downloads section .
Unfortuantely there´s no text file what has changed...
Could anybody tell us what is new in this DEV ?

Karsten

Hi I have a question regarding the Lipo-Alarm built in the software This is the code /* for V BAT monitoring after the resistor divisor we should get [0V;5V]->[0;1023] on analog V_BATPIN with R1=33k and R2=51k vbat = [0;1023]*16/VBATSCALE */ #define VBAT // comment this line to suppress the vbat cod...

Here you can find a video of the strange behaviour.
http://www.youtube.com/watch?v=SRHUm4uqcEM&context=C4571d8cADvjVQa1PpcFP3N6DelcM3B6UbCRI2d94Udi6Zo0tEJKs=

What the hell... ok, the problem is still there... What I´ve done: - change the Arduino Pro Mini test : no effort -change the BMA 020 test: no effort -change the WMP test: no effort ===???=== I´ve changed everything besides the Jussiboard and the MAG still doesn´t run !! Have somebody ever had such ...

Hello I have a strange problem with my HMC5883 on my Jussi-Shield V1.2. These sensors are installed: -orign. WMP -BMA020 -HMC5883 -BMP085 In the GUI everything is ok, gyro, mag, roll, directions, I can activate the MAG and it goes green in the GUI, no I2C Errors. BUT when I fly, the copter doesn´t r...

Hi Now I have setup the I2C-GPS and everything is working fine in the GUI (Satfix, all Sensors... everything how it should be) I have the Flyduino GPS (FMP04) First flight outside with the 2.0pre3 : Very stable ok, I got Satfix and 9 satelites.. I walked with the copter approx. 30meters from the sta...

I have still a problem with my yaw and the MAG

When I tilted the system in all direction, the orientation initially follows and then slowly drifting back to level

The MAG doesn´t work when I fly.

What do I have to change ?!

Greets
Karsten

Hi I hope you can help me... I´ve read main of this thread, but couldn´t find somethin regarding my problem. Now I´ve installed the I2C-GPS and in the GUI I can see GPS-fix (8 satelites) and the Distance to home is about 0-2m When I move with the copter and the notebook, the Distance rises... but on...

Because I have 3 Copter with the Arduino Pro Mini. I don´t want to buy the Mega-Board.

Hi Nils,

I´m using a second arduino with the I2c gps from Eosbandi. The FMP04 with the GPS Bob is connected to this 2. arduino (5V,TX,RX,Gnd)
Connection Serial serial, I2C I2C is correct...

Hi My WiiBoard doesn´t find any satelite. I suppose it´s because the Baud-rate of my GPS. It´s from Flyduino and it is set to 38400. .In the Multiwii 2.0pre2 I set the baud rate to 38400 (may I do this !?) Can I just change these lines from the serial GPS software (Eosbandi): Serial.begin(115200); /...

Hello. I´ve read this complete thread and now there´re a lot of questions. First: the link to Eosbandi Software for the second arduino (m) doesn´t work. I cannot found the software on this page. second: Could anybody tell me how to connect the second arduino pro mini to the main arduino.. is it corr...