Search found 10 matches
- Thu Jan 24, 2019 5:56 pm
- Forum: Getting Started - MultiWii config and setup
- Topic: help setting up PPM on MultiWii
- Replies: 6
- Views: 4879
Re: help setting up PPM on MultiWii
I tried but when I put the ch5 (aux1) switch on high level nothing happens... the only thing I noticed is that while keeping the throttle stick on bottom right position, the blue LED on FC start blinkinhg very fast (it seems almost solid) then it pause , then it blinks again and so on, what does thi...
- Thu Jan 24, 2019 11:28 am
- Forum: Getting Started - MultiWii config and setup
- Topic: help setting up PPM on MultiWii
- Replies: 6
- Views: 4879
Re: help setting up PPM on MultiWii
Ok I'll try unchecking the BARO box this evening, but why with the switch on low position I could't arm using the sticks? if I check arm on aux arming by sticks is disabled? I already tried without checking anything in arm
- Thu Jan 24, 2019 12:52 am
- Forum: Getting Started - MultiWii config and setup
- Topic: help setting up PPM on MultiWii
- Replies: 6
- Views: 4879
Re: help setting up PPM on MultiWii
The Board need to be level to ARM. #define ONLYARMWHENFLAT //prevent the copter from arming when the copter is tilted You can test to Arm with a AUX switch. I always was able to arm the motors using MSP before, I calibrated the accelerometer and the quad is flat on the floor. I also tried to set on...
- Fri Jan 18, 2019 1:33 am
- Forum: Getting Started - MultiWii config and setup
- Topic: help setting up PPM on MultiWii
- Replies: 6
- Views: 4879
help setting up PPM on MultiWii
Hello, I'm trying to set up my new Turnigy Evolution transmietter and TGY-iA6C receiver on my MultiWii SE V2.5. so far I've controlled the FC using a python script that inject RC channel via MSP. I read here https://hobbycomponents.com/rc/489-crius-se-25-multiwii-flight-controller that it supports P...
- Mon Jan 14, 2019 10:37 pm
- Forum: Shields, boards and sensors
- Topic: MultiWii SE V2.5 logic voltage is 3.3v?
- Replies: 9
- Views: 7295
Re: MultiWii SE V2.5 logic voltage is 3.3v?
thank you , it will probably be my next upgrade.
another question, can I connect my MultiWii FC to this TGY-IA6C receiver and how?
another question, can I connect my MultiWii FC to this TGY-IA6C receiver and how?
- Tue Jan 08, 2019 11:27 am
- Forum: Software
- Topic: Autonomous Quadcopter simultanious PWM and MSP commands
- Replies: 1
- Views: 10803
Re: Autonomous Quadcopter simultanious PWM and MSP commands
Hi, did you find a solution to this? Thanks
- Tue Jan 08, 2019 11:25 am
- Forum: Shields, boards and sensors
- Topic: MultiWii SE V2.5 logic voltage is 3.3v?
- Replies: 9
- Views: 7295
Re: MultiWii SE V2.5 logic voltage is 3.3v?
therefore I'm looking for a new FC with these specs:
- cheap
- MSP compatible
- best hovering (immobile, for stable video) and precision of maneuverability
- with GPS functions
can you suggest me one or some (with pros and cons)?
Thanks
- cheap
- MSP compatible
- best hovering (immobile, for stable video) and precision of maneuverability
- with GPS functions
can you suggest me one or some (with pros and cons)?
Thanks
- Thu Dec 27, 2018 7:01 pm
- Forum: Shields, boards and sensors
- Topic: MultiWii SE V2.5 logic voltage is 3.3v?
- Replies: 9
- Views: 7295
Re: MultiWii SE V2.5 logic voltage is 3.3v?
PatrikE wrote:Looks like PI is only connected to RX on MWIi board.
Then it will probably work fine.
yes but I'd like to be sure because it was really hard to find this FC , is not there a detailed datasheet?
- Thu Dec 27, 2018 12:39 pm
- Forum: Shields, boards and sensors
- Topic: MultiWii SE V2.5 logic voltage is 3.3v?
- Replies: 9
- Views: 7295
Re: MultiWii SE V2.5 logic voltage is 3.3v?
Hi, The Multiwii boards with Atmega 328 usually have 5V logic level. You need a level converter to protect the PI if it don't handle 5V. Logic Level Convert can be found everywhere on Ebay etc ( Logic Level Converter Module Bi-Directional for Arduino 5V-3V ) /Patrik and what about the link on instr...
- Sun Dec 23, 2018 8:05 pm
- Forum: Shields, boards and sensors
- Topic: MultiWii SE V2.5 logic voltage is 3.3v?
- Replies: 9
- Views: 7295
MultiWii SE V2.5 logic voltage is 3.3v?
I'm using a Raspberry to control a MultiWii Flight Controller V2.5 by using this https://it.aliexpress.com/item/FTDI-Basic-Breakout-USB-TTL-6-PIN-5V-Module-Fio-Pro-RGB-Lilypad-Program-Downloader-For/32709195540.html?af=20181224clvjfsptoph0&aff_platform=promotion&cpt=1545591759487&sk=jiMV...