MultiWii

Hi
I am a bit confused, at the moment i have two Navigatron V.2 from Flytron that works with AXN1.51_2722_3329_384.1151100.5 and I2C_GPS_NAV-v2.1rc2 on Atmega 328.
Is this the last possibility for Navigatron V.2 or can improve ?
Thanks in advance

I am very saddened to tell you that Fabio Varesano, the manufacturer of FreeImu died on Christmas Day. He was only 27 years of age. This morning we attended his funeral. I remember him as a friend with a great desire to try and help others. I apologize for the announcement. I came just now aware, t...

I am very saddened to tell you that Fabio Varesano, the manufacturer of FreeImu died on Christmas Day. He was only 27 years of age. This morning we attended his funeral. I remember him as a friend with a great desire to try and help others. it s so sad......it s so young to died how it s possible?i...

I am very saddened to tell you that Fabio Varesano, the manufacturer of FreeImu died on Christmas Day.
He was only 27 years of age.
This morning we attended his funeral.
I remember him as a friend with a great desire to try and help others.

baro is not necessary... but something I noticed.... Unless baro/ alt hold is toggled "on", it seems like my quad always wants drop altitude upon returning home. Is this just my imagination( a result of wind/ switching from ff to a hover) or is it returning to the original "home"...

Hi
I have a doubt, using RTH must I use the barometer or it is non necessary ?
Thanks in advance

Thanks EOSBandi
Now it works perfectly with 20120618 version, also the BT is OK.

Hi
Is the Gps working only with R33 or it is also included in the last dev version 20120618 ?
Thanks in advance

Tifani wrote:Hi !
I use BlueSky RC BT module @115200 v2.1B hangs when using bluetooth connection. Previous version work fine with the same module.
Regards & Thanks
Tom

Hi
The same for me.
Thanks

Hi, I need your help I cannot flash Gps with PowerFlash. First of all I flashed Atmega 328 on the navigatron V2 with a "Blink" sketch. Second I have crossed TX/RX on FTDI cable. I am able to see NEMEA Sentences and I can change parameters with MiniGps, but when I try to flash Gps using Po...

Hi, I need your help I cannot flash Gps with PowerFlash. First of all I flashed Atmega 328 on the navigatron V2 with a "Blink" sketch. Second I have crossed TX/RX on FTDI cable. I am able to see NEMEA Sentences and I can change parameters with MiniGps, but when I try to flash Gps using Pow...

@Sharkcopter To change parameters at runtime you can use MiniGPS and press ctrl+alt+s to enable setup mode. This "ctrl+alt+s" cost me a day until I found this hint;-) Changes will be lost if backup voltage is gone. New fixed power on defaults can be flashed with new firmware only but I di...

Hi Is it the same to change parameters in the Gps module using MiniGps 1.7.1 or I must to change using PowerFlash ? Another question, I note that connecting to Gps FTDI using RX/TX crossed cable I can read NEMEA sentences but I can not change parameters, if I want to change parameters I have to flas...

Hi
Please can someone help me on the meaning of the blue and red LED on the card Navigatron V2 ?
What means the flashing ?
Thanks in advance

Hi Warthox Very great video..
I have two questions about your video.
Is necessary to leave on the barometer when using the RTH?
Help the magnetometer in RTH?
Thanks

Hi

I'm starting with Gps and I have only two switch Aux1 and Aux2.
I have a doubt, is it the following schema correct ?

Thanks in advance

Hi I have a little problem. I bought a navigatron V2 and have to connect it to arduino i2c promini. I also have a V 0.4.3 freeimu who wants the arduino internal pullup disconnected because it has its internal. Navigatron V2 has no pullup resistors, can I connect to i2c in parallel or should I put ot...

Hi @ EosBandi thanks for your efforts. Yesterday I bought a Navigatron V2 and I realized that it defaults is 10 hz 115200 bps. I understand that i have no change anything, is this correct ? Care to share a link where you purchased your Navigtron? Thank you. Right from Flytron, yesterday was in stoc...

Hi
@ EosBandi thanks for your efforts.

Yesterday I bought a Navigatron V2 and I realized that it defaults is 10 hz 115200 bps.
I understand that i have no change anything, is this correct ?

I think no, I have a three wire serial LCD with Gnd / +5 V / Rx that i use for other quadri with 1.8p2 and work fine.
I enabled # define LCD_SERIAL3W.

I installed the latest dev released on my quadri bat now I can not change more parameters with my LCD (three-wire, with the 1.8p2 works perfectly).
There is a bug?
On the LCD I can see MultiWii parameters confused with strange characters and seems that there is an overflow.
Thanks in advance
Sergio